Machine Assembly And Operation; Product Liability - Tennant MB12004 - B1 Manuel Opérateur

Correct use
•
All single-disc machines are intended exclusively for use in build-
ing interiors.
•
Any use beyond this is considered incorrect. The manufacturer
accepts no liability for any resultant damage; the user alone bears
the risk.
•
Correct use also includes adherence to the operating, servicing
and maintenance conditions recommended by the manufacture.
•
The relevant accident prevention regulations as well as all the
generally acknowledged safety and working practices must be fol-
lowed.
•
Unauthorized modifications to the machine exclude the manufac-
turer's liability for resultant damage.
•
Before machine use, floorcoverings must be tested for suitability
for this cleaning process.
•
Pay attention to the area compression of point-elastic floors, e.g. in
gymnasiums
•
The manufacturer accepts no liability for damage to equipment and
to the floor being cleaned from using the wrong brushes and clean-
ing agents.
•
Machines may not be used in combination with an extension cord.

Product liability

The operator's attention is drawn explicitly to the fact that the ma-
chines may only be used for their intended purpose. If the machines
are not used for their intended purposes, the user must accept full
responsibility. Any liability of the manufacturer is thus excluded.
Sources of risk
WARNING: The single-disc machine is not
suitable for cleaning surfaces which release health-
hazardous dusts and liquids. Do not use
chine on steps.
WARNING: This machine is only intended for
use on level surfaces with a maximum gradient of up
to 2 %.
WARNING: This machine is not approved for
use on public paths and roads.
WARNING: Use only the brushes provided
with the appliance or those specified in the instruc-
tions. The use of other brushes may impair safety.
WARNING: When the machine is stationary,
the brush unit must be immediately switched off to
prevent damage to the floorcovering.
WARNING: During transportation in lifts, the
currently valid user instructions and safety regula-
tions and particularly those concerning maximum
loading must be observed.
Machine operation position
The machine operation position is behind the machine.
the ma-
- 4 -
Home Find... Go To..
Approved maintenance staff
The single-disc machine may only be serviced and repaired by per-
sons with technical and legal authorization.
Cleaning agents
•
When using cleaning and care agents, the manufacturer's danger
warnings must be followed and protective goggles and clothing
must be worn.
•
Only use low-foaming, non-combustible cleaning agents which do
not contain generally health-hazardous substances.
Explicit reference is made to the risks of using highly flammable, com-
bustible, toxic, health-hazardous, corrosive or irritant substances.

Machine assembly and operation

Initial operation
•
Delivery, instruction on safety procedures, handling and mainte-
nance and initial operation are generally carried out by our author-
ized specialist.
•
If this is not the case, the operator is responsible for instructing
machine users.
•
Please remember that the voltage in the building being cleaned
must concur with that given on the machine's type plate.
Assembly instructions
•
The motor head and shaft are supplied in separate packaging.
•
First undo the four hexagon socket screws in the shaft adjustment
unit (16) as far as it will go.
•
Align the handle bar (1) parallel to the wheels (9) with the open
side of the upper shaft housing (3) facing the rear.
•
Then feed the shaft (7) gently into the shaft adjustment unit (16)
until it will go no further.
•
Then tighten the hexagon socket screws.
•
Coil the electric cable around the handlebar (1) and the cable hook
(8).
Preparations for use
•
Grasp the handlebar (1) with both hands and tip the machine back
so it rests on its two wheels (9) (A).
•
Then run the machine to place of work and attach the pad.
•
To this end, slide the pad with its central recess over the yellow
connector and fasten it with the yellow fastening nut.
•
Make sure that the pad is properly centred and tighten the nut
firmly.
•
It must not protrude beyond the pad surface.
•
Before starting the machine, set the front wheel (11) to its maxi-
mum height, which is equal to the lowest pressing force.
•
Make sure that the swivelling action is unimpaired.
•
If the cleaning effect and gloss finish are unsatisfactory, increase
the pressing force slightly.
•
Only set the lowest possible pressure.
•
Always uncoil all of the mains cable (20 m).
EN