Description Des Interfaces Se Référant À Cei 61850; Aperçu Des Composants; Eléments De Données Spécifiques Au Tapcon® 260 - MR TAPCON 260-RTE Instructions De Service

7 Description des interfaces se référant à CEI 61850
7 Description des interfaces se référant à CEI 61850
7.1 Aperçu des composants
• TAPCON® 260
• Carte SID
• Câble réseau avec fiche RJ45
36
Declaration
Mod Mode
Beh Behaviour
Health health
NamPlt name plate
PhyNam name plate
PhyHealth health
Proxy Indicates proxy
Mod Mode
Beh Behaviour
Health Health
NamPlt Name plate
Loc Local operation
TapChg Change Tap Position
ParOp Parallel/Independend
LTCBlk Block Automatic Control
Auto Automatic/Manual operation
HiTapPos High tap position
LoTapPos Low tap position
CtlV Control Voltage
LodA Load Current (percentage of nominal load current)
BndCtr Band center voltage
BndWid Band width voltage (as percent of nominal voltage, FPF presumed)
CtlDlTmms Control intentional time delay (FPF presumed, in seconds)
LDCR Line drop voltage due to line resistance component (voltage)
LDCX Line drop voltage due to line reactance component (voltage)
BlkLV Control voltage below which auto Lower commands blocked (voltage)
LimLodA Limit Load Current (LTC Block Load Current, percentage)
Line Drop Compensation is R and X or Z model (0=R and X, 1=Z
LDC
compensation)
TmDlChr Time delay linear or inverse characteristic (0=lin., 1=inv.)
Line drop voltage due to line total impedance (percentage of nominal
LDCZ
voltage)
RegAuto REG.AUTO (Regulation AUTO)
K2Adj VC+DVC2 (Coefficient for adjustment of desired voltage Uref2)
K3Adj VC+DVC3 (Coefficient for adjustment of desired voltage Uref3)
K4Adj VC+DVC4 (Coefficient for adjustment of desired voltage Uref4)
BndCtrSel1 VC+DVC1 (Band center selection)
BndCtrSel2 VC+DVC2 (Band center selection)
BndCtrSel3 VC+DVC3 (Band center selection)
BndCtrSel4 VC+DVC4 (Band center selection)
MotDrv Motor drive active
VoltViol U.ANORMA (group signal lower U, U higher)
INRegul IN.REGUL (AVR Blocking - Overload)
StepErr NON.BLOC (tap position refereeing w.o success)
ParErr défaut configuration (Configuration error)
UnderV undervoltage
OverV overvoltage
UnderVReg tension basse (lower U)
OverVReg tension haute (U higher)
RegBloc blocage régleur réussi (AVR Blocking - Successful)
CBOpen régulation HS-DJ THT ouvert (Automatic OFF - CB HV open)
TTErr Fusion fusible (Automatic OFF - Blown Fuse)
InvalV absence tension (Automatic OFF - Absence of voltage)
StepUpper régleur en position haute (OLTC - Upper end position)
StepLower régleur en position basse (OLTC - Lower end position)
DFReg DF.REGUL (Anomaly OLTC)
7.2 Eléments de données spécifiques au
TAPCON® 260
Description
TAPCON® 260 RTE
readable/
writeable
R
R
R
R
R
R
R
R
R
R
R
R
R&W
R&W
R&W
R
R
R
R
R
R&W
R&W
R&W
R&W
R&W
R&W
R&W
R&W
R&W
R&W
R&W
R&W
R&W
R&W
R&W
R&W
R&W
R&W
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
1801010/02 FR