Safety Instructions For Installation And Maintenance Work; Danger In The Event Of Non-Observance Of The Safety Instructions; Transport And Storage Before Use; Safety Instructions For The Operator - Wilo SiFire EN Série Notice De Montage Et De Mise En Service

English
2.3 Danger in the event of non-observance of the
safety instructions
Non-observance of the safety instructions can
result in risk of injury to persons and damage to
the environment and the product/unit. Non-
observance of the safety instructions results in
the loss of any claims to damages.
In detail, non-observance can, for example, result
in the following risks:
• Danger to persons from electrical, mechanical and
bacteriological influences,
• Damage to the environment due to leakage of
hazardous materials.
• Property damage
• Failure of important product/unit functions
• Failure of required maintenance and repair proce-
dures

2.4 Safety consciousness on the job

The safety instructions included in these installa-
tion and operating instructions, the existing
national regulations for accident prevention
together with any internal working, operating and
safety regulations of the operator are to be com-
plied with.

2.5 Safety instructions for the operator

This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervi-
sion or instruction concerning use of the appliance
by a person responsible for their safety. Children
should be supervised to ensure that they do not
play with the appliance.
• If hot or cold components on the product/the unit
lead to hazards, local measures must be taken to
guard them against touching.
• Guards protecting against touching moving com-
ponents (such as the coupling) must not be
removed whilst the product is in operation.
• Leakages (e.g. from the shaft seals) of hazardous
fluids (which are explosive, toxic or hot) must be
led away so that no danger to persons or to the
environment arises. National statutory provisions
are to be complied with.
• Highly flammable materials are always to be kept
at a safe distance from the product.
• Danger from electrical current must be eliminated.
Local directives or general directives [e.g. IEC, VDE
etc.] and local power supply companies must be
adhered to.
2.6 Safety instructions for installation and
maintenance work
The operator must ensure that all installation and
maintenance work is carried out by authorised and
qualified personnel, who are sufficiently informed
from their own detailed study of the operating
instructions.
Work on the product/unit must only be carried out
when at a standstill. It is mandatory that the pro-
cedure described in the installation and operating
30
instructions for shutting down the product/unit
be complied with.
Immediately on conclusion of the work, all safety
and protective devices must be put back in posi-
tion and/or recommissioned.
2.7 Unauthorised modification and manufacture of
spare parts
Unauthorised modification and manufacture of
spare parts will impair the safety of the product/
personnel and will make void the manufacturer's
declarations regarding safety.
Modifications to the product are only permissible
after consultation with the manufacturer. Original
spare parts and accessories authorised by the
manufacturer ensure safety. The use of other
parts will absolve us of liability for consequential
events.

2.8 Improper use

The operating safety of the supplied product is
only guaranteed for conventional use in accord-
ance with Section 4 of the operating instructions.
The limit values must on no account fall under or
exceed those specified in the catalogue/data
sheet.

3 Transport and storage before use

The system fire extinguishing booster is supplied
on a pallet. It is protected from moisture and dust
by a plastic bag.
The equipment must be transported by means of
authorised load devices. (See example on fig. 1)
WARNING! Risk of personal injury!
The static stability of the unit must be taken into
account. Handling of the material must be car-
ried out by qualified personnel, using only suita-
ble and authorised equipment.
Lifting straps must be fastened to the ring bolts
placed on the base frame.
The manifolds do not fit with the handling of the
system and should not be used to fix loads in
transit.
CAUTION! Risk of product damages!
Handling by using discharge manifold can cause
leakages!
When the product is delivered, check it for any
damage in transit. In case of damage, take any
necessary measures from the delivery company
(forwarding agent).
CAUTION! Risk of product damages!
If the product shall be installed later on, store it
in a dry place. Protect it from impacts and any
outside influences (moisture, frost, etc. ...). Han-
dle the product with care.
WILO SE 12/2019