A L Ign In G T He R Un N In G Belt - Tunturi J4F Mode D'emploi

weight and slow speed put particular strain on the
device and therefore demand greater lubrication.
The running deck requires periodic lubrication.
With average usage (30 minute workout session 3
times a week), lubricate every four to six months.
You may adjust the timing of the lubrication based
on the intensity of the treadmill use level. To check
the lubrication level, simply lift the running belt,
and put your hand as far into the center of the
belt as you can reach. If your hand shows signs of
lubricant (some wetness), then it does not need
additional lubrication. If the board feels dry and
there is very little evidence of lubricant on your
hand, then additional lubrication should be added
as instructed:
Stop running belt so belt seam is located on the
1.
top and in the center of the deck.
Insert nozzle into spray head of lubricant can.
2 .
Lift running belt.
3 .
Position nozzle between the belt and the board
4 .
approximately 200 mm (8") from the front of the
treadmill.
Apply T-Lube from the front to the rear of the
5.
treadmill on each side of the treadmill. Try to reach
the spray as far into the center of the running deck
as possible.
The treadmill is instantly ready for use.
6 .
Lubricate your treadmill only with T-Lube
N O T E !
lubricant. Contact your local Tunturi distributor
for supplies of T-Lube.
C LE A NIN G T H E TR EAD MILL
Wipe the treadmill surfaces, especially the
handlebars and meter from dust with a damp cloth
or towel. Do not use solvents. Use a small vacuum
nozzle to carefully vacuum around all visible
components (belt, running deck, side rails etc.).
To clean the underside of the treadmill, lift the
running deck to the storage position.
Also keep the area near the treadmill clean.
N O T E !
While in use, the treadmill gathers dust that may
cause problems in the operation of the equipment.

A L IGN IN G T HE R UN N IN G BELT

Monitor belt tracking during exercise and make
adjustments as needed. The belt should run in the
center of the treadmill. Alignment is not usually
needed, provided
•
the treadmill is placed on an even, solid
and horizontal surface and the belt is correctly
tensioned
•
the alignment of the belt is correct
It is, however, possible for the belt to be pushed to
one side due to the user's running style (e.g. more
weight on one foot). The alignment of the belt is
adjusted by turning the two bolts at the back of the
treadmill.
8
Align the belt according to the following
instructions:
Turn the power switch on and increase the
1.
treadmill's speed to 5 km/h (3 mph).
. If the belt drifts to the left, turn the left
2
adjustment bolt 1/4 turn clockwise and the right
adjustment bolt 1/8 turn anti-clockwise. If the belt
drifts to the right, turn the right adjustment bolt
1/4 turn clockwise and the left adjustment bolt 1/4
turn anti-clockwise.
If the belt remains centered the adjustment is
3 .
correct. If not, continue to make small adjustments
as above until the belt is correctly aligned. If the
belt is allowed run across to one side for long
periods of time the edges of the belt may be
damaged and the treadmill may not continue to
operate correctly. Any damage to the belt caused
by the lack of necessary adjustment will not be
covered by the warranty.
A DJ US TI NG TH E BE LT T EN S ION
The belt must be tensioned if it begins to slip on
the rollers. In normal use, however, keep the belt
as loose as possible! The belt tension is adjusted by
turning the same screws as used for aligning the
running belt. If turning the screws will not effect
the belt tension, please contact your local Tunturi
dealer.
Increase the treadmill's speed to 5 km/h (3
1.
mph).
Turn both adjustment screws an equal amount,
2 .
1/4 turn clockwise.
Try to slow the belt down by holding onto the
3 .
handrails and braking as you walk (as if you were
walking downhill). If the belt slips, turn another
1/4 turn and repeat the test. When braking heavily
the belt may slip. If the belt keeps slipping despite
repeated adjustments, please contact your local
Tunturi dealer.
M AL F UN CT ION S
Despite continuous quality control,
N O T E !
defects and malfunctions caused by individual
components may occur in the equipment. In most
cases it's unnecessary to take the whole device in
for repair, as it's usually suffi cient to replace the
defective part. Always give the model, serial
number of your equipment and in case of
malfunctions also conditions of use, nature of
malfunction and any error code.
When you encounter unusual behavior from the
treadmill, simply turn the power switch off, wait 1
minute and turn the power switch on to reset the
treadmill. This should clear incidental errors and
ready the treadmill for normal operation again. If
after you have reset the treadmill by turning the
power switch off and on again, and the treadmill
is still not operational, contact your local Tunturi
dealer for service.