Maintenance; Adjusting The Belt Tension; Malfunctions - Tunturi T60F Mode D'emploi

BEHIND". When you are ahead of your previously
saved session, the display will read "YOU ARE x.xx
AHEAD".
Once the profile has been completed, the treadmill
4.
will automatically stop. You can save your workout in
the console's memory (see Memory Function).

MAINTENANCE

The equipment is safe to use only when periodically
maintained and inspected for faults and wear. Do not
attempt any servicing or adjustment other than those
described in this manual. Any other servicing must
be performed by an authorized service representative.
Check the tightness of all fixing screws once a year.
Do not overtighten. Defective components must be
immediately replaced: the equipment must not be
operated with any defective components.
CLEANING AND LUBRICATING THE TREADMILL
Wipe the treadmill surfaces, especially the handlebars
and console from dust with a damp cloth or towel. Do
not use solvents. Use a small vacuum nozzle to carefully
vacuum around all visible components (belt, running
deck, side rails etc.). To clean the underside, lift the
running deck to the storage position.
Also keep the area near the treadmill clean.
NOTE!
While in use, the treadmill gathers dust that may cause
problems in the operation of the equipment.
In average domestic use (a maximum of 60 minutes a
day), you should check the lubrication approximately
after every 300 hours of use. The console is equipped
with a counter for measuring total values, thus
allowing you to monitor your total training time on
the treadmill. If there is any jerky movement of the
belt, always check the lubrication level. To do this, let
the treadmill come to a complete stop, then simply lift
the running belt to feel the running deck; if the deck
feels dry and there is very little evidence of lubricant on
your hand, lubricate the running deck according to the
following instructions:
Attach the nozzle to the lubricant container.
1.
Let the treadmill come to a complete stop, and then
2.
lift the running belt.
Position nozzle between the belt and the board
3.
approximately 200 mm (8") from the front of the
treadmill.
Apply T-Lube from the front to the rear of the
4.
treadmill on each side of the treadmill, spraying as far
into the center of the running base as possible. One T-
Lube container will be sufficient for two re-lubrications.
The treadmill is instantly ready for use.
5.
When lubricating the treadmill, you should let it
NOTE!
run at least five minutes before lifting the running deck
to the storage position. This will prevent the lubricant
from spilling.
Lubricate your treadmill only with T-Lube S
NOTE!
silicon lubricant. Contact your local Tunturi distributor
for further supplies of T-Lube.
O W N E R ' S M A N U A L
ALIGNING THE RUNNING BELT
Monitor belt tracking during exercise and make
adjustments as needed. The belt should run in the
center of the treadmill. Alignment is not usually needed,
provided
•
the treadmill is placed on an even, solid and
horizontal surface and the belt is correctly tensioned
•
the alignment of the belt is correct
It is, however, possible for the belt to be pushed to one
side due to the user's running style (e.g. more weight
on one foot). The alignment of the belt is adjusted by
turning the two bolts at the back of the treadmill.
Turn the power switch on and increase the treadmill's
1.
speed to 5 km/h (3 mph).
If the belt drifts to the left, turn the left adjustment
2.
bolt ¼ turn clockwise and the right adjustment bolt 1/8
turn anti-clockwise. If the belt drifts to the right, turn
the right adjustment bolt ¼ turn clockwise and the left
adjustment bolt ¼ turn anti-clockwise.
If the belt remains centered the adjustment is correct.
3.
If not, continue to make small adjustments as above
until the belt is correctly aligned. If the belt is allowed
run across to one side for long periods of time the edges
of the belt may be damaged and the treadmill may not
continue to operate correctly. Any damage to the belt
caused by the lack of necessary adjustment will not be
covered by the warranty.

ADJUSTING THE BELT TENSION

The belt must be tensioned if it begins to slip on the
rollers. In normal use, however, keep the belt as loose
as possible! The belt tension is adjusted by turning the
same screws as used for aligning the running belt. If
turning the screws will not effect the belt tension, please
contact your local Tunturi dealer.
Increase the treadmill's speed to 5 km/h (3 mph).
1.
Turn both adjustment screws an equal amount, ¼
2.
turn clockwise.
Try to slow the belt down by holding onto the
3.
handrails and braking as you walk (as if you were
walking downhill).
If the belt slips, turn another ¼ turn and repeat the test.
When braking heavily the belt may slip. If the belt keeps
slipping despite repeated adjustments, please contact
your local Tunturi dealer.

MALFUNCTIONS

Despite continuous quality control, defects and
NOTE!
malfunctions caused by individual components may
occur in the equipment. In most cases it's unnecessary
to take the whole device in for repair, as it's usually
sufficient to replace the defective part. Always give
the model, serial number of your equipment and in
case of malfunctions also conditions of use, nature of
malfunction and any error code.
When you encounter unusual behavior from the
treadmill, simply turn the power switch off, wait 1
GB
•
T 6 0 F
11