Miller Auto-Line XMT 350 CC/CV Manuel De L'utilisateur page 13

Keep flammables away from cutting. Do not cut near flammables.
Welding sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
Do not cut on drums or any closed containers.
�
Une liste complète de pièces détachées est disponible sur www.MillerWelds.com
Do not fuel a hot engine.
Do not fuel a hot engine.
Do not fuel a hot engine.
Welding sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
Cutting sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
Do not grip material near cutting path.
Use lift eye to lift unit and properly installed accessories only, not gas cylinders. Do not exceed maximum lift
Use lift eye to lift unit and properly installed accessories only, not gas cylinders. Do not exceed maximum lift e
Use lift eye to lift unit and properly installed accessories only, not gas cylinders. Do not exceed maximum lift
Cutting sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
rating (see Specifications).
rating (see Specifications).
Do not weld on drums or any closed containers.
/
rating (see Specifications).
Turn off power before disassembling torch.
Writer: If necessary, replace the word "handle" with "lift eye'.
Do not use one handle to lift or support unit.
Do not weld on drums or any closed containers.
When power is applied failed parts can explode or cause other parts to explode.
Do not cut on drums or any closed containers.
When power is applied failed parts can explode or cause other parts to explode.
When power is applied failed parts can explode or cause other parts to explode.
Do not remove or paint over (cover) the label.
Do not spray water on electrical parts, including Engine Control Unit (ECU).
Drive rolls can injure fingers.
Do not cut on drums or any closed containers.
Flying pieces of parts can cause injury. Always wear a face shield when servicing unit.
Flying pieces of parts can cause injury. Always wear a face shield when servicing unit.
Do not grip material near cutting path.
Flying pieces of parts can cause injury. Always wear a face shield when servicing unit.
Recycle or dispose of used coolant in an environmentally safe way.
Welding wire and drive parts are at welding voltage during operation
Always wear long sleeves and button your collar when servicing unit.
Turn off power before disassembling torch.
Do not grip material near cutting path. Always wear long sleeves and button your collar when servicing unit.
Always wear long sleeves and button your collar when servicing unit.
Hot Parts can burn. Do not touch hot parts bare-handed. Allow cooling period before handling parts or equip-
ment.
Consult rating label for input power requirements.
After taking proper precautions as shown, connect power to unit.
Turn off power before disassembling torch. After taking proper precautions as shown, connect power to unit.
Connect Green Or Green/Yellow grounding conductor to ground terminal first. After taking proper precautions as shown, connect power to unit.
Do not remove or paint over (cover) the label.
Connect input conductors (U/L1, V/L2, W/L3) to line terminals.
Writer: If necessary, replace the word "handle" with "lift eye'.
Become trained and read the instructions and labels before working on machine.
Disconnect input plug or power before working on machine.
Disconnect input plug or power before working on machine.
Do not remove or paint over (cover) the label.
Do not use one handle to lift or support unit.
Disconnect input plug or power before working on machine.
Environmental Protection Use Period (China)
Drive rolls can injure fingers.
Connect Green Or Green/Yellow grounding conductor to ground terminal first.
Connect input conductors (L1, L2, L3) to line terminals.
Wire
Welding wire and drive parts are at welding voltage during operation
Feed wire between guide pins into drive rolls.
Keep your head out of the fumes
Consult rating label for input power requirements.
Become trained and read the instructions and labels before working on machine.
Les étincelles de soudage risquent de provoquer un incendie. Tenir
un extincteur d'incendie à proximité, et demander à un surveillant de
se tenir à proximité, prêt à s'en servir.
<12.4 V
Ne pas effectuer de soudures sur des cylindres ou des conteneurs
fermés.
+ +
Ne pas enlever ou recouvrir l'étiquette de peinture.
Les morceaux ou pièces éjectées peuvent blesser. Toujours porter un
masque pour faire l'entretien de l'appareil.
Porter des manches longues et boutonner son col pour faire l'entre-
tien de l'appareil.
Après avoir pris les précautions indiquées, brancher l'alimentation de
l'appareil.
Ne pas lever ou soutenir l'appareil par une seule poignée.
Période d'utilisation pour protection de l'environnement (Chine)
Porter une casquette et des lunettes de sécurité. Porter des protège-
Wear hat and safety glasses. Use ear protection and button shirt
oreilles et un col de chemise à boutons. Porter un casque de soudage
collar. Use welding helmet with correct shade of filter. Wear complete
équipé d'un verre de protection de teinte appropriée. Utiliser une pro-
body protection.
tection totale pour le corps.
Wear hat and safety glasses. Use ear protection and button shirt
Become trained and read the instructions before working on the
Recevoir une formation convenable et lire les instructions avant de
collar. Use welding helmet with correct shade of filter. Wear complete
machine or welding.
procéder au soudage ou aux interventions exécutées sur le poste.
body protection.
Become trained and read the instructions before working on the
Become trained and read the instructions before working on the
machine or cutting.
machine or welding.
Become trained and read the instructions before working on the
machine or cutting.
Remove unit from shipping crate. Remove Owner's Manual from unit.
Read Owner's Manual for battery maintenance information.
keep hands and metal objects away.
Use lifting eye to lift unit and properly installed units only.
Use a proper cart to move unit.
keep hands and metal objects away.
Safe
Safe1
Safe
Safe
Safe
Safe
Safe1
Safe1
Safe
Safe1
Safe
Safe
Safe
Safe
Safe11 Safe
Safe31 2017 04
Safe
Safe2
Safe2
Safe
Safe2
Safe2
Safe 11
Safe32 2012 05
Safe Safe
Safe2
Safe
Safe
Safe11
Safe33 2017 04
Safe2
Safe2
Safe
Safe
Safe2
Safe120
Safe34 2012 05
Safe
Safe
Safe2
Safe2
Safe
Safe12
Safe
Safe
Safe2
Safe
Safe
Safe12
Safe35 2012 05
Safe
Safe12
Safe36 2012 05
Safe
Safe12
Safe38 2012 05
Safe7 2017 04
Safe39 2012 05
Safe40 2012 05
Safe
Safe41 2012 05
Safe40 2012 05
OM-2254 Page 7
Safe