Publicité
As a safety measure, maintenance should be performed on the generating set regularly and carefully by people who have the
necessary experience and are equipped with suitable tools, in respect of current regulations. The maintenance operations to be
carried out are detailed in the maintenance table. The interval for this is supplied as a guide and for generating sets operating with
fuel and oil which conform to the specifications given in this manual. The maintenance intervals can be shortened depending on the
generating set's operating conditions and requirements. It is important to note that the warranty shall not be valid if generating set
maintenance has not be performed correctly.
5.1
Reminder of use
Ensuring maintenance is performed regularly and correctly will guarantee safety and performance. The oil, filter elements and,
where present, the spark plug, are consumables which must be in good condition for the unit to operate correctly. Replace
them regularly as often as is needed (the reference for ready-to-use maintenance kits is given in the table of technical
specifications where applicable). The warranty becomes void in the event of failure to respect the maintenance recommendations.
For any questions about a special operation, please contact your nearest agent who will advise and help you.
5.2
Maintenance table
Operation to be carried out at whichever deadline
is reached first:
Clean the unit
Unit
Replacing the spark plug
Reference to be ordered:
Clean the filter
Fuel
Replace the filter
Reference to be ordered:
Clean the foam element
Air filter
Replace the foam element
Reference to be ordered:
Note: for the fuel, use a mix of unleaded petrol and 2% approved two-stroke oil (2T). During the running-in period (approximately the first 20 hours),
use a mix with 5 to 6.5% two-stroke oil (2T).
5.3
Performing the maintenance operations
1.
Shut down the unit and wait at least 30 minutes for it to cool.
2.
Disconnect the cap(s) of the spark plug(s) and disconnect the negative "-" terminal on the battery (if fitted).
3.
Carry out maintenance in accordance with the information given in this manual and, to avoid the risk of damage to the unit,
only use original parts or their equivalent.
5.3.1
Replace the fuel filter
1.
Unscrew the fuel tank cap (A2-C1) and remove it.
2.
Remove the fuel filter (A10-C2) from the fuel tank.
3.
Replace the used fuel filter with a new one.
4.
Refit the fuel filter in the fuel tank, then screw the fuel tank cap back on.
5.3.2
Clean or replace the air filter
IMPORTANT
If the filter element is excessively dirty or damaged (torn, pierced), it is essential to replace it a with new element and at least every 3
cleans.
1.
Unlock the air filter cover (D2 & D1) and remove it.
2.
Remove the foam element (D3) to clean.
3.
Wash it in soapy water, carefully rinse it and leave it to dry completely.
4.
Soak it in a little clean engine oil and squeeze it to remove any excess oil (do not wring it out).
If there is too much oil remaining in the foam, the unit will emit smoke when it is first started.
5.
Carefully check that there are no tears or holes in the foam element: replace it if it is damaged.
6.
Refit the foam element, then refit the air filter cover and lock it.
5.3.3
Replace the spark plug.
1.
Disconnect the spark plug cap (E1).
2.
Use a dry air spray to clean the spark plug wells.
3.
Use a spark plug spanner to unscrew the spark plug (A12-E2) and discard it.
4.
Fit a new spark plug in position and tighten it by hand to avoid damaging the threads.
5.
Use a spark plug spanner to tighten the spark plug by 1/2 turn after it is seated to compress the washer.
After:
1
Risk of fire or explosion: for a foam element, only use soapy water and clean engine oil during this
operation.
Every:
month/first
3 months/50
st
20 hours
hours
X
X
X
X
17/110
Section 5. Servicing the motor pump
Every:
6 months/100
2 years/300
hours
X
X
330490433
maintenance
must only be
X
carried out by
X
330490426
X
0.806.800.107
X
330490417
Every:
hours
General
one of our
agents.
France:
(call charge)
Publicité
