Migatronic PI 320 DC Manuel D'instruction page 21

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 41
The control signals from the TIG torch are transmitted
to the machine through the circular 7-pin plug (7).
When the plug has been assembled please secure it
by turning the "circulator" clockwise. Connect the gas
hose to the quick connection.
COATED ELECTRODES: Electrodes are marked with
a polarity on the packing. Connect the electrode
holder in accordance with this marking to the plus or
minus sockets of the machine.
Connection of TIG torch
Mount the flow hose on the water cooled torch in the
quick connection marked with blue (8) and the return
hose in the quick connection marked with red (9).
Connection of a separated water cooling unit
(PI 350)
Fasten the module under the machine with the fitting
(13). Mount the 4-poled plug (15) in the corresponding
socket in the machine (14). Mount the flow hose on
the water cooled torch in the quick connection marked
with blue (8) and the return hose in the quick
connection marked with red (9).
Control of cooling liquid
If the machine is delivered with water cooling, the
cooling liquid level should be checked regularly by
means of the level control (10). The refilling of cooling
liquid takes place through the filler neck (11).
Connection of electrode holder for MMA
The electrode holder and return current cable are
connected to plus tap (6) and minus tap (5). Observe
the instructions from the electrode supplier when
selecting polarity.
Connection of foot control
Foot control is connected to the 7-poled plug (7) or
through the 8-poled plug (12) (depending on the foot
control type).
Connection of remote control
PI machines equipped with 8-pole control interface
(12) can be controlled via a remote control or a
welding robot. The remote control socket has
terminals for the following functions:
A: Input signal for welding current, 0 –
+10V input impedance: 1Mohm
B: Signal ground
C: Arc detect – contact of relay (max.
1Amp), fully insulated
D: N.C.
E: Arc detect – contact of relay (max. 1Amp), fully
insulated
F: N.C.
G: Supply +24VDC. Short circuit protected with PTC
resistor (max. 50mA).
H: Supply ground
CWF Multi (option)
It is possible to connect to the PI with up to 8 CWF
Multi units via dedicated CAN BUS connector (16)
placed on the rear side of machine (option). In order to
permit this control capability, enter the USER Menu
and select "Fdr" (feeder), then access "Act" (Active
devices) and set the parameter to 1. (see USER
MENU)
Now the PI is ready to control the CWF directly from
the box: for each TIG welding program it is possible to
select what CWF unit must be activated and the
relative CWF program in the range 1 to 20.
Depending from the settings on the CWF, if the unit is
in OFF mode the error message "Fdr" can be
displayed on PI and the welding procediment stopped.
This is to inform the user the CWF is not responding to
start signal from PI.
Usage of the machine
When welding, a heating of various components of the
machine takes place and during breaks these compo-
nents will cool down again. It must be ensured that the
flow is not reduced or stopped.
When the machine is set for higher welding currents,
there will be a need for periods during which the
machine can cool down.
The length of these periods depends on the current
setting, and the machine should not be switched off in
the meantime. If the periods for cooling down during
use of the machine are not sufficiently long, the over-
heating protection will automatically stop the welding
process and the yellow LED in the front panel will
come on. The yellow LED switches off when the
machine has cooled down sufficiently and is ready for
welding.
21

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Pi 350 dcPi 400 dcPi 500 dc

Table des Matières