Publicité
GB
the [POWER] button to start the system Default
free running mode 50%, low wind; If the power
failure memory power, the direct operation mem-
ory mode and wind speed; In the fixed working
mode, the machine is switched off and then
switched on. The fixed mode and wind speed
before the system is run are adopted. In the free
working mode (four LED lights in fixed mode are
off), it will be turned off and then into standby.
After starting up, the system will reset to the free
mode 50% with low wind.
2. press [FAN SPEED] button as follows:
– When the wind speed needs to be adjusted,
press the wind speed button to adjust the Quiet,
high and Low wind speed. When the corre-
sponding indicator light is on, the current wind
speed has been set.
3. Press [UP] and [DOWN] to enter the free dehu-
midification operation. The humidity is set to 35%-
- 80%, with 5%RH added and decreased each
time.
4. Press [MODE] to change the set value of humid-
ity as follows:
– Press [MODE] to select the fixed working
mode: [LIVING SPACE] (50%) [BASEMENT]
(45%) [CONTINUOUS] (continuous division
Wet CO) (55%) switch the sequential cycle, and
the corresponding mode indicator light is on.
5. press [TIMER] button can be timer setting:
– in shutdown state, press the timing button to set
the timing startup function. The timing light will
be on and the display will initially display 0.5.
Press [UP] and [DOWN] to adjust the time. The
timing indicator is on when there is a timing
function. In the timing process, press the timing
key again, then cancel the timing function.
– in the startup state, press the timing button to
set the timing shutdown function. The timing is
0.5 for the display of the bright display console.
At this point, press the [UP] and [DOWN] keys
to adjust the timing time.
– the range of timing time is set as 0.5-24h.
– after long pressing the timing button for 3 sec-
onds, the lock key function is turned on, the lock
light is on, and the other keys are invalid after
the lock key; Only after pressing the timing but-
ton again for 3 seconds to cancel the lock but-
ton function, will the other keys be effective
after the lock lamp is off.;
6. Press the [MIRAGE] key to open the display of
the front panel display, and press this key again to
close the display of the front panel display. The
display of the front panel is consistent with the dis-
play of the top display.
7. Reset the [FILTER] key:
– After the dehumidifier starts up and runs for
250h, the indicator light for cleaning the filter
screen will be on, reminding the filter screen to
be cleaned, pressing the button, timing again,
and the indicator light for cleaning the filter
screen will be off.
Draining The Collected Water
When the drainage tank is full, the tank full indicator
light will turn on, the operation will stop automatically
and the buzzer will beep 3 times to alert the user, that
the water need to be emptied from the drainage tank.
36
Emptying the Drainage Tank
► P. 4, fig. 1
– Lightly press on the sides of the tank with both
hands and pull the tank out gently.
► P. 4, fig. 2
– Discard the collected water
Note
► P. 4, fig. 3
• Do not remove the float from the water tank. The
water full sensor will no longer be able to detect
the water level correctly without the float and
water may leak from the water tank.
• If the drainage tank is dirty, wash it with cold or
lukewarm water. Do not use detergent, scouring
pads, chemically treated dust cloths, gasoline,
benzene, thinner, or other solvents, as these can
scratch and damage the tank and cause water
leakage
► P. 4, fig. 4
• When replacing the drainage tank, press the tank
firmly into place with both hands. If the tank is not
positioned properly, the [TANK FULL] sensor will
be activated, and the dehumidifier will not oper-
ate.
Cleaning and maintenance
DANGER! Risk of injury! Always pull
the mains plug out before commencing
any work on the device.
To clean the Body
– Wipe it with a soft damp cloth.
To Clean the Air Filter
► P. 5, fig. 1
– Open the inlet grill firstly and washed with water
► P. 5, fig. 2
– Attach the air filter
– Insert the filter into the grill smoothly, and place
the inlet grill into right place.
Storing the Dehumidifier
When the unit is not being used for a long period of
time and you want to store it note the following steps:
– Empty any water left in the drainage tank.
– Fold up the power supply cord and put it in the
water tank.
– Clean the air filter
– Discard in a cool and dry place.
Note for maintenance work
Checks to the area
Prior to beginning work on systems containing flam-
mable refrigerants, safety checks are necessary to
ensure that the risk of ignition is minimized repair to
the refrigerating system, the following precautions
shall be complied with prior to conducting work on the
system.
Work procedure
Work shall be undertaken under a controlled proce-
dure so as to minimize the risk of a flammable gas or
vapour being present while the work is being per-
formed.
Publicité
