Publicité
HTB200PP_DVQX2752ZAX1.book Page 13 Friday, August 2, 2024 3:03 PM
The device is connected but audio cannot be
heard through the system.
For some built-in Bluetooth
•
®
set the audio output to "SC-HTB200" manually.
Read the operating instructions of the device for
details.
Sound from the device is interrupted.
The device is out of the 10 m (33 ft) communication
•
range. Move the device nearer to the system.
•
Remove any obstacle between the system and the
device.
Other devices that use the 2.4 GHz frequency band
•
(wireless router, microwaves, cordless phones, etc.)
are interfering. Move the device nearer to the
system and distance it from the other devices.
HDMI
█
HDMI CEC related operations no longer function
properly.
Check the setting on the connected devices.
•
Turn on HDMI CEC function on the connected
–
devices.
Select this system as the speaker in the TV's
–
HDMI CEC menu.
When the HDMI connections are changed, after a
•
power failure or after the AC power supply cord has
been removed, HDMI CEC operations may not
function properly.
Turn on all the devices that are connected to the
–
TV with an HDMI cable and then turn on the TV.
Turn off the HDMI CEC settings of the TV and
–
turn it on again. For details refer to the operating
instructions for the TV.
While the system and the TV are connected with
–
an HDMI cable, turn on the TV, disconnect the AC
power supply cord of this system and then
connect it again.
Sound
█
No sound
•
Cancel muting. (
10)
•
Check the connections to the other devices.
(
8, 9)
Make sure that the received audio signal is
•
compatible with this system.
If the system is connected to the TV with an HDMI
•
cable only, make sure that the HDMI terminal of the
TV is labeled "HDMI (ARC)". If not, connect an
optical digital audio cable. (
Check the connections. Change the cables if the
•
connections are correct.
Check the audio output settings on the connected
•
device.
The dual audio cannot be changed from main to
secondary.
If the audio received from the connected device is
devices, you have to
•
not "Dolby Dual Mono" or the output setting is not
"Bitstream", the setting cannot be changed from this
system. Change the setting on the connected
device.
The volume is lowered when the system is turned
on.
"Volume limitation" is on. (
•
If the system is turned off with the volume above 50,
•
the volume will automatically set to 50 when you
turn on the system. (
The sound lags behind the image.
Depending on the TV, when this system is
•
connected to it via Bluetooth
from this system may lag behind the TV image.
Connect this system and the TV with an HDMI
cable/optical digital audio cable. (
The audio format indicator does not correspond
to the playback source.
If the playback source is Dolby Digital or DTS
•
the audio output setting of the connected equipment
(e.g., TV, player) to bitstream. For details, refer to
the operating instructions for the connected
equipment.
There is no audio.
The power of the unit turns off automatically.
(When the unit detects a problem, a safety measure is
activated and the unit automatically turns to standby
mode.)
There is a problem with the amplifier.
•
Is the volume extremely high?
•
If so, lower the volume.
Is this system placed in an extremely hot place?
•
If so, move this system to a cooler place and wait a
few moments and then try to turn it on again.
If the problem persists, confirm the indicators status,
turn off this system, disconnect the AC power supply
cord and consult your dealer. Please be sure to
remember the indicators status and inform the dealer.
8, 9)
11)
11)
, the sound output
®
8, 9)
, set
®
13
13
Publicité
