Publicité
EN
Transmitter Setup
IMPORTANT: After you set up your model, always rebind the transmitter and
receiver to set the desired failsafe positions.
The GEAR Channel (CH 5) controls the retractable landing gear. If you are using a 6
channel transmitter, The FLAP Channel (CH 6) can be used to toggle SAFE Select.
With the values listed below it will turn SAFE on for half and full ap positions and
AS3X will be on for no aps position.
To use the FLAP channel for the SAFE Select switch the values must be set to
+100 and -100 and the speed set to 0 temporarily to assign the safe switch in the
ap system menu. Then change the ap systems values back to the listing in the
transmitter setup. See the SAFE Select Switch Designation section of this manual
to assign the switch for SAFE Select.
For the rst ight, set the ight timer to 3 minutes 40 seconds. Adjust the time after
the initial ight.
NX Series Transmitter Setup
1. Power ON your transmitter, click on scroll wheel, roll to System Setup and
click the scroll wheel. Select YES.
2. Go to Model Select and choose Add New Model near the bottom of the list.
Select Airplane Model Type by choosing airplane image, select Create.
3. Set Model Name: Input a name for your model le.
4. Go to Aircraft Type and scroll to the wing selection,
choose Wing: 1 Ail 1 Flap Tail: Normal
5. Select Main Screen, Click the scroll wheel to enter the Function List.
6. Go to Servo Setup, Reverse: Reverse the GER channel
7. Go to D/R (Dual Rate) and Expo menu to set D/R and Expo.
8. Set Rates and Expo: Aileron
Set Switch: Switch F
Set High Rates: 100%, Expo 10% — Low Rates: 70%, Expo 5%
9. Set Rates and Expo: Elevator
Set Switch: Switch C
High Rates: 100%, Expo 10% — Low Rates 70%, Expo 5%
10. Set D/R (Dual Rate) and Expo: Rudder
Set Switch: Switch G
High Rates: 100%, Expo 10% — Low Rates 70%, Expo 5%
11. Set Throttle Cut; Switch: Switch H, Position: -100%
12. Select Flap System
Set Switch: Switch D
Set Flaps: POS 0: -100%, POS 1: -25%, POS 2: 55%
Set Elevator to Flap Mix: POS 0: 0%, POS 1: 11%, POS 2: 11%
Set Speed: 2.0
iX Series Transmitter Setup
1. Power ON your transmitter and begin once the Spektrum AirWare app is open.
Select the orange pen icon in the screen's upper left corner, the system asks
for permission to Turn Off RF, select PROCEED.
2. Select the three dots in the upper right corner of the screen,
select Add a New Model.
3. Select Model Option, choose DEFAULT, select Airplane.
The system asks if you want to create a new acro model, select Create.
4. Select the last model on the list, named Acro.
Tap on the word Acro and rename the le to a name of your choice.
5. Press and hold the back arrow icon in the upper left corner of the screen to
return to the main screen.
6. Go to the Model Setup menu. Select Aircraft Type. The system asks for
permission to Turn Off RF, select PROCEED. Touch the screen to select wing.
Select 1 Ail 1 Flap.
7. Press and hold the back arrow icon in the upper left corner of the screen to
return to the main screen.
8. Go to the Model Adjust menu.
6
www.modellmarkt24.ch
Dual Rates
Attempt your rst ights in low rate. For landings, use high rate elevator.
NOTICE: To ensure AS3X technology functions properly, do not lower rate values
below 50%. If less control de ection is desired, manually adjust the position of
the pushrods on the servo arm.
NOTICE: If oscillation occurs at high speed, refer to the Troubleshooting Guide
for more information.
Exponential
After rst ights, you may adjust exponential in your transmitter.
DX Series Transmitter Setup
1. Power ON your transmitter, click on scroll wheel, roll to System Setup and click
the scroll wheel. Select YES.
2. Go to Model Select and choose Add New Model at the bottom of the list.
The system asks if you want to create a new model, select Create.
3. Set Model Type: Select Airplane Model Type by choosing the airplane.
The system asks you to con rm model type, data will be reset. Select YES.
4. Set Model Name: Input a name for your model le.
5. Go to Aircraft Type and scroll to the wing selection,
choose Wing: 1 Ail 1 Flap Tail: Normal
6. Select Main Screen, Click the scroll wheel to enter the Function List.
7. Go to Servo Setup, Reverse: Reverse the GER channel
8. Set D/R (Dual Rate) and Expo: Aileron
Set Switch: Switch F
Set High Rates: 100%, Expo 10% — Low Rates: 70%, Expo 5%
9. Set D/R (Dual Rate) and Expo: Elevator
Set Switch: Switch C
High Rates: 100%, Expo 10% — Low Rates 70%, Expo 5%
10. Set D/R (Dual Rate) and Expo: Rudder
Set Switch: Switch G
High Rates: 100%, Expo 10% — Low Rates 70%, Expo 5%
11. Set Throttle Cut; Switch: Switch H, Position: -100%
12. Select Flaps
Set Switch: Switch D
Set Flaps: POS 0: -100%, POS 1: -25%, POS 2: 55%
Set Elevator to Flap Mix: POS 0: 0%, POS 1: 11%, POS 2: 11%
Set Speed: 2.0
iX Series Transmitter Setup
9. Go to Servo Setup, Reverse: Reverse the GER channel
10. Set Dual Rates and Expo: Select Aileron
Set Switch: Switch F
Set High Rates: 100%, Expo 10% — Low Rates: 70%, Expo 5%
11. Set Dual Rates and Expo: Select Elevator
Set Switch: Switch C
High Rates: 100%, Expo 10% — Low Rates 70%, Expo 5%
12. Set D/R (Dual Rate) and Expo: Rudder
Set Switch: Switch G
High Rates: 100%, Expo 10% — Low Rates 70%, Expo 5%
13. Select Flap System
Set Switch: Switch D
Set Flaps: POS 0: -100%, POS 1: -25%, POS 2: 55%
Set Elevator to Flap Mix: POS 0: 0%, POS 1: 11%, POS 2: 11%
Set Speed: 2.0
13. Set Throttle Cut; Switch: Switch H, Position: -100%
Viper 70mm EDF
Publicité
