Bien-Air Dental CHIROPRO L Instructions D'utilisation page 17

Default values
Implantology: default values
The table shows the default operating values for 8 different implantology sequences.
These default values represent common settings used during implant procedures.
Implant PRG1 /
Implant PRG2
PRG8
ROUND BUR 1 ROUND BUR
20:1 20:1
28.1 Ncm 28.1 Ncm
1'000 RPM 2'000 RPM
ROUND BUR 2 PILOT DRILL
20:1 20:1
28.1 Ncm 35.3 Ncm
1'000 RPM 800 RPM
DRILL 1 DRILL 1
20:1 20:1
35.3 Ncm 35.3 Ncm
800 RPM 800 RPM
DRILL 2 DRILL 2
20:1 20:1
35.3 Ncm 35.3 Ncm
600 RPM 800 RPM
DRILL 3 DRILL 3
20:1 20:1
35.3 Ncm 35.3 Ncm
500 RPM 800 RPM
DRILL 4 DRILL 4
20:1 20:1
35.3 Ncm 35.3 Ncm
400 RPM 800 RPM
TAPPING TAPPING
20:1 20:1
35.3 Ncm 35.3 Ncm
15 RPM 15 RPM
TAP UNSCREWING TAP UNSCREWING
20:1 20:1
42.5 Ncm 42.5 Ncm
15 RPM REV 15 RPM
IMPLANT SCREWING IMPLANT SCREWING
20:1 20:1
35.3 Ncm 35.3 Ncm
15 RPM 15 RPM
UNSCREWING UNSCREWING
20:1 20:1
54.7 Ncm 54.7 Ncm
15 RPM REV 15 RPM
Implant PRG3 Implant PRG4
ROUND BUR ROUND BUR
20:1
28.1 Ncm
1'000 RPM
DRILL 1
20:1
35.3 Ncm
800 RPM
DRILL 2
20:1
35.3 Ncm
800 RPM
DRILL 3
20:1
35.3 Ncm
800 RPM
DRILL 4
20:1
35.3 Ncm
800 RPM
DRILL 5
20:1
35.3 Ncm
800 RPM
TAPPING
20:1
35.3 Ncm
15 RPM
TAP UNSCREWING TAP UNSCREWING
20:1
42.5 Ncm
REV 15 RPM REV 15 RPM
IMPLANT SCREWING IMPLANT SCREWING
20:1
35.3 Ncm
15 RPM
UNSCREWING UNSCREWING
20:1
54.7 Ncm
REV 15 RPM REV 15 RPM
Implant PRG5
ROUND BUR
20:1 20:1
28.1 Ncm 28.1 Ncm
1'200 RPM 1'500 RPM
DRILL 1 DRILL 1
20:1 20:1
35.3 Ncm 35.3 Ncm
800 RPM 500 RPM
DRILL 2 DRILL 2
20:1 20:1
35.3 Ncm 35.3 Ncm
800 RPM 500 RPM
DRILL 3 DRILL 3
20:1 20:1
35.3 Ncm 35.3 Ncm
800 RPM 500 RPM
DRILL 4 DRILL 4
20:1 20:1
35.3 Ncm 35.3 Ncm
800 RPM 500 RPM
DRILL 5 DRILL 5
20:1 20:1
35.3 Ncm 35.3 Ncm
800 RPM 500 RPM
TAPPING TAPPING
20:1 20:1
35.3 Ncm 35.3 Ncm
15 RPM 15 RPM
TAP UNSCREWING
20:1 20:1
42.5 Ncm 42.5 Ncm
REV 15 RPM REV
IMPLANT SCREWING
20:1 20:1
35.3 Ncm 35.3 Ncm
15 RPM 15 RPM
UNSCREWING
20:1 20:1
54.7 Ncm 54.7 Ncm
REV 15 RPM REV
Implant PRG6 Implant PRG7
ROUND BUR PILOT DRILL 1
20:1 20:1
35.3 Ncm 28.1 Ncm
1'500 RPM 800 RPM
DRILL 1 PILOT DRILL 2
20:1 20:1
35.3 Ncm 28.1 Ncm
1'500 RPM 800 RPM
DRILL 2 DRILL 1
20:1 20:1
35.3 Ncm 35.3 Ncm
1'500 RPM 600 RPM
DRILL 3 DRILL 2
20:1 20:1
35.3 Ncm 35.3 Ncm
1'500 RPM 500 RPM
DRILL 4 DRILL 3
20:1 20:1
35.3 Ncm 35.3 Ncm
1'500 RPM 400 RPM
DRILL 5 SHAPING DRILL
20:1 20:1
35.3 Ncm 35.3 Ncm
1'500 RPM 250 RPM
TAPPING TAPPING
20:1 20:1
35.3 Ncm 35.3 Ncm
20 RPM 20 RPM
TAP UNSCREWING TAP UNSCREWING
20:1 20:1
42.5 Ncm 42.5 Ncm
15 RPM REV 20 RPM REV
IMPLANT SCREWING IMPLANT SCREWING
20:1 20:1
35.3 Ncm 35.3 Ncm
15 RPM 15 RPM
UNSCREWING UNSCREWING
20:1 20:1
54.7 Ncm 54.7 Ncm
15 RPM REV 15 RPM REV
17