Desoutter EAD105- 500 Mode D'emploi page 4

Safety Information
Model
EAD80-650
EAD105-500
EAD105-500-HAD
EAD160-430
EAD160-430-HAD
EAD200-370
EAD280-260
EAD280-370
EAD440-250
EAD660-160
Weight
Model kg
EAD20-1300 1.55
EAD32-900 1.55
EAD50-900 1.95
EAD50-900-HAD 1.80
EAD70-700-HAD 2.00
EAD70-800 2.15
EAD70-800 SQ 2.15
1/2
EAD80-650 2.55
EAD105-500 2.55
EAD105-500-HAD 2.40
EAD160-430 4.45
EAD160-430-HAD 4.3
EAD200-370 5.25
EAD280-260 5.25
EAD280-370 6.35
EAD440-250 8.65
EAD660-160 11.25
Storage and use conditions
Storage temperature
Operating temperature
Storage humidity
Operating humidity
Altitude up to
Usable in Pollution degree 2
environment
Indoor use only
Declarations
Liability
Many events in the operating environment may affect the
tightening process and shall require a validation of results. In
compliance with applicable standards and/or regulations, we
hereby require you to check the installed torque and rota-
All manuals and user guides at all-guides.com
rpm
650
500
500
430
430
370
260
370
250
160
lb
3.41
3.41
4.30
3.96
4.40
4.74
4.74
5.62
5.62
5.29
9.81
9.5
11.57
11.57
13.99
19.07
24.80
-20 to +70 °C (-4 to +158 F)
0 to 45 °C (32 to 113 F)
0-95 % RH (non-condensing)
0-90 % RH (non-condensing)
2000 m (6562 feet)
tional direction after any event that can influence the tighten-
ing result. Examples of such events include but are not lim-
ited to:
• initial installation of the tooling system
• change of part batch, bolt, screw batch, tool, software,
configuration or environment
• change of air- or electrical connections
• change in line ergonomics, process, quality procedures
or practices
• changing of operator
• any other change that influences the result of the tighten-
ing process
The check should:
• Ensure that the joint conditions have not changed due to
events of influence.
• Be done after initial installation, maintenance or repair
of the equipment.
• Occur at least once per shift or at another suitable fre-
quency.
EU DECLARATION OF CONFORMITY
We, Ets Georges Renault, 38 rue Bobby Sands, 44818 Saint
Herblain, France, declare under our sole responsibility that
the product (with name, type and serial number, see front
page) is in conformity with the following Directive(s):
2006/42/EC, 2014/30/EU, 2011/65/EU
Harmonized standards applied:
EN 62841-2-2:2015 + AC1:2015, EN 61000-3-2:2014, EN
61000-3-3:2013, EN 61000-6-2:2005, EN
61326-2-3:2013EN 60745-2-2 :2010, EN 55014-1 :2006/
A1 :2009+A2 :2011, EN 55014-2 :1997/A2:2008, EN
61000-3-2 :2006/A1-A2 :2009, EN 61000-3-3 :2008, EN
61000-6-2 :2005, EN 61326 -2-3 :2013
Authorities can request relevant technical information from:
Pascal ROUSSY, R&D Manager, 38 rue Bobby Sands,
44818 Saint Herblain, France
Saint-Herblain, 2020/06/24
Pascal ROUSSY, R&D Manager
Signature of issuer
Noise and Vibration Declaration Statement
• Sound power level < 70 dB(A) , uncertainty 3 dB(A), in
accordance with EN 62841-2-2:2015.
• Vibration total value < 2.5 m/s
accordance with EN 62841-2-2:2015.
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. The vibration emis-
sion level may be used for a preliminary assessment of expo-
sure. These declared values are not adequate for use in risk
4 / 204
2 2
, uncertainty 3 m/s , in
10/2020