Publicité
Les langues disponibles
Les langues disponibles
•
Do not modify or remove any of the original component parts of the product, if not recommended by MSA.
•
Do not apply paint, stickers, cleaning products with a hydrocarbon base or solvents to the helmet or visors
to prevent damaging the materials.
•
Some conditions can exceed this helmet's capacity to protect against serious injury or death.
•
Never use this helmet as a vehicular or sports helmet.
•
Never store gloves, cigarettes, earplugs or similar objects between the suspension and the shell liner. This
space is needed when the shell/ suspension absorbs the energy of an impact.
•
Use only MSA supplied or approved accessories with this helmet.
•
The helmet must not be thrown, dropped or used as a support.
•
No harmful material was used. In case of allergic reaction, exit the danger zone and remove the PPE. Eye
and face protectors material that touches your skin can cause an allergic reaction to susceptible
individuals.
•
For the right selection of the eye protection always consult a safety supervisor.
•
Tinted over spectacles are not suitable for driving at night or in low light conditions.
•
Eye and face protectors worn over non-designated corrective frames may transmit impacts which may
damage the corrective eye wear thus creating a hazard to the user.
•
Service life of eye and face protectors depends on the conditions of use.
•
Check eye and face protectors marking to ensure that the protector is sufficient for the intended activity.
•
The eye and face protectors and arc flash earflaps only perform as expected in use position (low position).
•
Any eye and face protectors that have been scratched, dropped or damaged must be replaced.
•
The eye and face protectors are designed exclusively for assembly on MSA V-Gard 900 helmet type.
•
The eye and face protectors could be damaged by some chemical substances.
•
If the symbols F, B, or A are not common to both the visor and the frame then it is the lower level which
shall be assigned to the complete eye protector.
•
Face shield complying with field of use symbol 8, must be equipped with a scale number 2-1,2 or 3-1,2 and
must have a minimal thickness of 1.4 mm.
•
For a visor to comply with field of use symbol 9, both the visor and adapters must be marked with one of the
symbols F, B or A.
•
If protection from high-speed particles at extreme temperatures is necessary, make sure that your
protective equipment (oculars and face shield) shows the symbol T directly after the impact symbol (F, B,
or A). If the symbol T does not show after the impact symbol, the protective equipment can only be used to
supply protection from high-speed particles at room temperature.
•
The arc flash earflaps must not be worn in the up position if there is any risk of molten metal splashes.
•
The helmet and shell accessories (eye and face protectors excluded) can be used at temperatures up to –
30 °C.
•
Do not adjust arc flash earflaps in temperatures of –10 °C and below.
•
Protection can be reduced because of aging or inappropriate cleaning method, insulating is limited
depending on conditions of use.
•
Always check the markings on the face shields to confirm the level of protection against short electric arc.
Checking the markings on the frame alone is not sufficient.
•
Face shields are assigned to the highest light transmittance class 0 (LT Class 0). Under normal working
conditions no additional lighting is required. However, always check your ability to see colors in the working
environment before using this product.
Failure to follow these warnings can result in serious personal injury or death.
2
Use
2.1
Helmet Adjustment
The helmet must be adjusted to the size of the user's head to ensure adequate protection. Size range with Fas-Trac
III harness: 52 cm to 63 cm.
1.
Push top crown strap towards top of helmet.
2.
Place helmet on head and push down until a comfortable wearing height is reached.
3.
To ensure that headbands are compatible with head height and to get the preferred upward vision (change
of vision angle), adjust the helmet wearing height if necessary by repositioning the headband clips within
the suspensions. →
GB
Figure 1
.
2 Use
5
Publicité
