Rotors; Cleaning; Service; Appendix - StarLab N2631-0017 Mini Fuge Plus Mode D'emploi

7

Rotors

The centrifuge is supplied with two interchangeable quick release rotors. No tools are required
to exchange the rotors or attach them to the motor shaft. The rotors can be easily exchanged
with one hand by way of the quick release system. To remove a rotor, place your thumb on top
of the motor shaft and place two fingers underneath the rotor and lift off the shaft. To replace a
rotor, simply position on the moter shapft and snap in to place.
8

Cleaning

Before using any cleaning or decontamination methods except those recommended by the manu-
facturer, check with the manufacturer that the proposed method will not damage the equipment.
To clean the centrifuge, use a damp cloth and a mild, non-corrosive detergent (ph <8). After clea-
ning, ensure all parts are dried thoroughly before attempting to operate the unit. Do not immerse
the centrifuge in liquid or pour liquids over it.
9

Service

Contact STARLAB at www.starlabgroup.com if you have a question about the centrifuge or if
the unit requires servicing. Please do not send in a unit for service without first obtaining a returns
number and a decontamination form. All units returned must be decontaminated and accom-
panied by a decontamination form. Ensure the unit is properly packed to avoid damage - any
damage resulting from improper packaging will be the responsibility of the user.

10 Appendix

10.1 Symbols and Conventions

Symbols that may be used in this manual or on the product.
CAUTION!
This symbol refers you to important operating and maintenance (servicing) instructions
within the product Instruction Manual. Failure to head this information may present a
risk of damage or injury to persons or equipment
8
· Mini Fuge Plus · Manual
7.0 Rotors
The centrifuge is supplied with two interchangeable quick release rotors. No tools are required to exchange
the rotors or attach them to the motor shaft. The rotors can be easily exchanged with one hand by way of
the quick release system. Removal of the rotors is done by placing your thumb on top of the motor shaft
and lifting up with two fingers under the rotor. Place the other rotor into position on the motor shaft and
snap in.
8 place tube rotor
8.0 Cleaning
Before using any cleaning or decontamination methods except those recommended by the manufacturer, check
with the manufacturer that the proposed method will not damage the equipment. To clean the centrifuge, use
a damp cloth and a mild, noncorrosive detergent (ph <8). After cleaning, ensure all parts are dried thoroughly
before attempting to operate the unit. Do not immerse the centrifuge in liquid or pour liquids over it.
9.0 Service
Should you have a question about the operation of the Mini Centrifuge or if service is required, contact Corning
at: 800-492-1110. Do not send in a unit for service without first calling to obtain a repair authorization number.
Should the unit require return to Corning for service, it should be properly packed to avoid damage. Any
damage resulting from improper packaging shall be the responsibility of the user.
10.0 Appendix
10.1 Spare Parts
6770-RT
6770-RTS
6770-RTA.5
6770-RTA.2
6770-RTA.25
401025
10.2 Symbols and Conventions
The following chart is an illustrated glossary of the symbols that may be used in this manual or on the
product.
CAUTION This symbol refers you to important operating and maintenance (servicing)
instructions within the product Instruction Manual. Failure to head this information may
present a risk of damage or injury to persons or equipment
10.3 Equipment Disposal - European Regulations
According to Directive 2012/19/EU of the European Parliament and of
the Council of 4 July 2012 on waste electrical and electronic equipment
(WEEE), Labnet C1601-B Mini centrifuge is marked with the crossed-out
wheeled bin and must not be disposed of with domestic waste.
Consequently, the buyer shall follow the instructions for reuse and recycling
of waste electronic and electrical equipment (WEEE) provided with the
products and available at the following link: www.corning.com/weee
8 place tube rotor for Mini Centrifuge
4 place PCR strip rotor for Mini Centrifuge
Adapter, 0.5ml tubes
Adapter, 0.2ml tubes
Adapter, 0.25ml tubes
Power Adapter, 24V for Mini Centrifuge
4 place strip rotor
Mini Centrifuge | 3