Vortice AIRLINK 30 Livret D'instructions page 43

ENGLISH
To set the SSID in the case of two installed networks (for example two networks on two different
!
floors) follow these steps:
1) Switch off the units that are not part of the network on which you want to operate (for
example those on the upper floor if you want to set the network on the lower floor) to prevent
them not to be assigned the same SSID.
2) Then, from the MASTER unit, assign the unique network identifier (SSID) by pressing the
MODE - MODE - SPEED - SPEED - MODE – MODE buttons in sequence and then the SPEED
button.
3) To set up another network (the upper floor in the example), you do not need to turn off the
units of the other set up network as they already have a unique SSID.
To reset the mesh WiFi network (global / all network units) SSID:
• Press the SPEED - MODE - FUNCTION buttons at the same time.
• Press the MODE - SPEED - FUNCTION - MODE - SPEED- FUNCTION buttons in sequence.
• Press the MODE button within 20 second
• All the speed LEDs from 1 to 5 will flash briefly to indicate execution of the command:
- Reset the SSID = VORTICE_HRW (default) FOR ALL UNITS ON THE NETWORK.
• If the MODE button is not pressed within 20 seconds, all speed LEDs 1 to 5 will light up for 1 second without
flashing, indicating that the machine will return to normal operation without resetting the network SSID.
To reset the WiFi mesh network (local / single unit on the network) SSID:
• Press the SPEED - MODE - FUNCTION buttons set as SLAVE at the same time.
• Press the MODE - MODE - SPEED - SPEED - MODE - MODE buttons in sequence..
• Press the SPEED button within 20 seconds
• All the SPEED LEDs from 1 to 5 will blink briefly to indicate that SSID = VORTICE_HRW (default) has been
reset FOR THE SINGLE UNIT ONLY.
• If the SPEED button is not pressed within 20 seconds, all SPEED LEDs from 1 to 5 will light up for 1 second
without blinking to indicate that the appliance will return to normal operation without resetting the network
SSID.
MAC Address and SSID
The MAC Address is assigned by the manufacturer of the Wi-Fi module itself and it is unique.
The last 4 hexadecimal digits of the MAC Address (UAA = Unique Address Assignment) of the master unit are
used to generate the unique SSID of the network:
VOR_XXXXXXXX (e.g. VOR_34F5E4E7)
Each digit consists of two hex characters ranging from 0 to 255 (0x00-0xFF).
The default SSID is instead VORTICE_HRW with default password = "12345678" which cannot be changed.
Adding one or more new units to an existing mesh network
1. Go into programming mode by pressing simultaneously the SPEED - MODE - FUNCTION buttons.
2. From any unit of this network, reset all the network identifiers (SSID) of each unit in the existing network by
pressing the MODE - SPEED - FUNCTION - MODE - SPEED - FUNCTION buttons in sequence and then the
MODE button.
3. Or, if there are units with unknown SSIDs or which are different from the network SSID, set each unit to SLAVE
mode by pressing the MODE - MODE - SPEED - SPEED - FUNCTION - FUNCTION buttons in sequence and
then the SPEED button. Afterwards set the default identification (SSID) on each unit by pressing in sequence
the buttons MODE - MODE - SPEED - SPEED - MODE - MODE and then the SPEED button.
4. If a MASTER unit has not yet been defined, a network unit must be set as MASTER by pressing the MODE -
MODE - SPEED - SPEED - FUNCTION - FUNCTION buttons in sequence and then the MODE key..
5. Finally assign the unique network identification (SSID) from the MASTER unit by pressing the MODE - MODE
- SPEED - SPEED - MODE - MODE buttons in sequence and then the SPEED button.
43