Télécharger Imprimer la page

ST CP1 434 Serie Manuel D'utilisation page 51

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 70
Behaviour
• Exercise caution when reversing or moving backwards. 
Look behind you to make sure there are no obstacles
before and during operations in reverse gear.
• Never run, always walk.
• Do not allow the lawnmower to pull you along.
• Always keep hands and feet away from the cutting means, 
when starting and when using the machine.
• Attention:  the  cutting  means  will  continue  to  rotate  for 
a  few  seconds  after  disengagement  or  after  you  have 
switched off the engine.
• Keep away from the discharge opening.
• Do not touch the engine parts as they get very hot when 
running. Danger of burns.
If something breaks or an accident occurs during
mowing, turn off the engine immediately and move
the machine away to prevent further damage; if
an accident occurs with injuries or third parties
are injured, carry out the first aid measures most
suitable for the situation immediately and contact
the medical authorities for any necessary health
care. Carefully remove any debris which could
cause damage or injury to persons or animals
if ignored.
Use limitations
• Never  operate  the  machine  with  damaged,  missing 
or incorrectly assembled guards (grass catcher, side
discharge guards  rear discharge guards).
• Don't use the machine if the attachments/tools are not
installed in their seats.
• Never disengage, deactivate, remove or tamper with the 
safety systems/micro switches installed.
• Do  not  alter  the  engine  adjustments,  nor  over-run  it.  If 
the engine is forced to work with an excessive number of 
rotations, the risk of personal injury increases.
• Do not strain the machine too much and do not use a
small machine for heavy-duty work. If you use the right 
machine, you will reduce the risk of hazards and improve 
the quality of your work.
1.4. MAINTENANCE, STORAGE AND TRANSPORT
Ensure regular maintenance and correct storage to maintain
machine safety and high performance levels.
• Never  use  the  machine  with  worn  or  damaged  parts. 
Faulty  or  worn-out  parts  must  always  be  replaced  and 
never  repaired.  Use  original  replacement  parts  only: 
the use of non-original and/or incorrectly fitted parts will 
jeopardise the safety of the machine, may cause accidents
or personal injuries for which the Manufacturer is under 
no circumstance liable or responsible. 
• To reduce the risk of fire, regularly check the machine for 
oil and/or fuel leaks.
• While adjusting the machine, pay attention to avoid getting
your fingers caught between the moving cutting device 
and the fixed parts of the machine .
• Do not store the machine with fuel in the tank in an area 
where fuel vapours could reach a naked light, a spark or 
a strong heat source.
• To reduce fire risks, do not leave containers with debris 
inside a room.
The noise and vibration levels shown in these
instructions are the maximum levels for use of
the machine. The use of an unbalanced cutting
element, the excessive speed of movement, or
the absence of maintenance have a significant
influence on noise emissions and vibrations.
Consequently, it is necessary to take preventive
steps to eliminate possible damage due to high
levels of noise and stress from vibration. Maintain
the machine well, wear ear protection devices,
and take breaks while working.
1.5. ENVIRONMENTAL PROTECTION
• Scrupulously comply with local regulations for the disposal 
of  packaging,  deteriorated  parts  or  any  elements  with 
a  strong  environmental  impact;  this  waste  must  not  be 
disposed of as normal waste, it must be separated and 
taken  to  specified  waste  disposal  centres  where  the 
material will be recycled.
• Scrupulously comply with local regulations for the disposal 
of waste materials
• When  the  machine  is  withdrawn  from  service,  do  not 
dispose  of  it  in  the  environment,  but  take  it  to  a  waste 
disposal facility in accordance with the local regulations 
in force.
2.
PRODUCT DESCRIPTION
This machine is pedestrian controlled lawnmower.
The machine essentially consists of an engine, which drives 
a cutting device enclosed in a casing, equipped with wheels 
and a handle.
The operator is able to operate the machine and use the main
controls, always staying behind the handle at a safe distance 
from the rotating cutting means.
If the operator leaves the machine, the engine and cutting
means will stop within a few seconds.
Intended use and improper use
This machine is designed and built for cutting grass in gardens
and grassy areas.
Any other usage may be hazardous and harm persons and/
or damage things.
Examples of improper use may include, but are not limited to:
• transporting other people, children or animals on the
machine;
• being transported by the machine;
• using the machine to tow or push loads.
• operate the cutting device in non grassy areas;
• using the machine for collecting leaves or debris;
• using the machine to trim hedges, or for cutting vegetation
other than grass;
• use of the machine by more than one person.
IMPORTANT Improper use of the machine will invalidate the
warranty, relieve the Manufacturer from all liability, and the user
will consequently be liable for all and any damage or injury to
himself or others.
This  machine  is  intended  for  use  by  consumers,  i.e.  non-
professional  operators. The  machine  is  intended  for  "DIY" 
use only.
IMPORTANT The machine must be used by one operator.
EN - 2

Publicité

loading

Ce manuel est également adapté pour:

Cp1 484 serieCp1 534 serie