Emerson AVENTICS PROFINET-IO Instructions De Montage page 26

3. Make sure the system or system part is not under pressure or voltage.
4. Protect the system against being restarted.
5. Allow product and adjacent system parts to cool down.
6. Wear PPE.
Visual inspection
Visually inspect for integrity.
u
Detailed inspection
• Identifications and warnings on the product: The system owner has to replace
labels or warnings that are difficult to read immediately.
• Check the compressed air connections.
• Check the lines.
• Check the seals.
• Check to make sure that all fittings are properly connected.
• Check the safety devices on the system.
• Check the product functions.
9.2 Cleaning
9.2.1 General requirements
Cleaning intervals
• The system owner specifies the cleaning intervals in line with the ambient
conditions at the operating site.
Aids
• Only clean the product with damp cloths.
• Only use water for cleaning and a mild detergent, if necessary (material pro-
tection).
NOTICE! Make sure that no water or water mist can enter the product via the
compressed air connections. Penetrating fluids destroy seals and cause dam-
age to the product.
9.2.2 Procedure
1. Close all openings with suitable safety devices so that no cleaning agent can
enter into the system.
2. Remove all dust deposits from the product and the adjacent system parts.
3. If necessary, remove other production-related deposits from the product and
the adjacent system parts.
9.3 Maintenance
In normal ambient conditions, the product is maintenance-free.
9.4 After service
If no damage has been detected and the operator has not reported any malfunc-
tions, the product can be reconnected to the power supply and put back into op-
eration.
10 Disassembly and exchange
Disassembly is only required if the product has to be exchanged, installed in a dif-
ferent location or disposed off.
10.1 Preparation
Implement safety measures. See
u
Tools
• 1x hex key (size 3)
AVENTICS™ PROFINET-IO | R412015162-BAL-001-AF | English
g 11.2.2 Implementing safety measures.
10.2 Procedure
4
4
1
1
2
2
3 3
Fig. 11: Replace and disassemble bus coupler
1 Hexagonal socket-head screws
3 Seal
5 Tie rod
1. Make sure the system or system part is not under pressure or voltage.
2. Disconnect electrical connections from the bus coupler.
3. Release end plate (2x hexagon socket screws each).
4. Optional: release I/O modules.
5. Pull off all elements from the tie rods.
6. Slide the bus coupler onto the tie rods.
7. Ensure that the tie rods are fully screwed in.
8. Make sure that seals are inserted correctly.
9. Optional: Slide the I/O modules back onto the tie rods.
10.Slide end plate back onto tie rods and screw tight.
Tightening torque: 2.5 ... 3.0 Nm.
11.Make all presettings at the bus coupler.
12.Establish connections.
13.Check configuration and adjust if necessary.
11 Conversion and extension
11.1 Planning
11.1.1 Installation conditions
General requirements
• Make sure that the product is installed in a manner that protects it from all
types of mechanical loads.
• Make sure that there is sufficient space.
Product-specific requirements
• Mounting orientation. See g 15. Technical
• Do not exceed the current load of 0.5 A per output (material protection).
• Expand the valve system with a maximum of 6 input modules or output mod-
ules.
Ambient conditions
• Let the product acclimatize for a few hours before installation. Otherwise wa-
ter may condense in the housing.
• Keep the installation location free from vibration.
• Protect the product from direct sunlight and UV radiation.
11.1.2 Required accessories, materials and tools
Select material and tools that are suitable for your product configuration. De-
pending on the configuration, you will need further accessories.
5
5
6
6
3
2 Left end plate
4 Bus coupler
6 Left end plate with connections
data.
26