Deltaplus LV102200 Notice D'utilisation Et D'entretien page 12

Adhere strictly to the instructions for use, verification, maintenance and storage.
This product is inseparable from a comprehensive fall protection system (EN363), whose function is to minimize the risk
of body injury from falls and it must be removed after the use. It should be a personal issue item, where this is applicable
Before any use, refer to the recommendations for use for each component of the system.
After use, remove the device and store it properly
The fall arrest harness (EN361) is the only body grip to be allowed for use with a fall arrest system.
The fall arrest harness (EN361) may be connected to its attachment point A, to a connection element or component in
personal protection fall arrest systems (restraint systems, work positioning systems (EN358), fall arrest systems (EN353-
1, EN353-2, EN355, EN360), access systems via ropes and rescue systems).
The fall arrest harness (EN361) is connected to other elements of the system by connectors (EN362).
In these cases, follow the instructions described in their own manual.
WARNING:
This anchoring device (EN795) will never be directly connected to a harness.
This anchoring device shall only be used in a PPE fall arrest system. Any other use can jeopardize the safety of the user.
INTRODUCTION:
LV102 is an anchor ring complies to European standard « EN795:2012 type B ».
Ring anchor strap, high resistance, 100% polyester, width 45mm, steel D-Ring
Its conception allows to use it on any kind of structure with different shapes, defined in the table of references.
The maximum sizes of the host structures must have the sections as defined in the table of references
TECHNICAL SPECIFICATIONS:
MATERIALS: (See reference table).
D ring: stainless steel
Strap, high resistance, 100% polyester
ESTABLISHMENT AND/ OR ADJUSTMENTS:
The installation of the device must be made according to the instructions of the installation manual of the device.
The user's safety depends on the efficiency of the device installation.
Follow step by step the instructions and recommendations of the manufacturer in order to guarantee a suitable
installation.
Use the appropriate tools for the described actions which do not damage the device.
Choose a strong structure, minimum 12kN. The user must ensure that the support materials in which the structural anchor
devices are attached are adapted for this constraint.
WARNING:
The attachment point must be located above the user and the work carried out in such a way, as to minimise both the
potential for falls and potential fall distance and it must have a minimum resistance of 12kN according to EN795.
Anchor LV102 will be connected to the anchor point of the host structure via a connector.
RECOMMENDATIONS:
For safety reasons and before each use, check:
- that the anchorage complies to the instructions
- that the anchorage is appropriately installed
- the D attachment is correctly positioned.
- that the device does not show any sign of corrosion
- that the yearly control of the device is still valid
- that the operating instructions described for each component of the system are met.
- that the general disposition of the work situation reduces the fall risk, the drop height and the pendulum movement in
the case of a fall.
- the vertical clearance is sufficient (free space beneath the feet of the user) and no obstacles disrupt the normal
functioning of the fall arrest system.
The vertical clearance is the stopping distance H + additional safety distance of 1 m. The distance H measured from the
initial position to the final position (user's balance after the fall arrest).
Check that there is enough height below the user according to the equipment used. A height of 2m minimum must be
left below the user's feet. Check that the overall layout restricts swinging to a minimum if a fall should occur.
WARNING:
Under no circumstances should the user open, adjust or operate the equipment when using the LV102.
These manipulations can be performed only when the risk of falling is avoided.
Before each use, check that the anchor is securely fixed on its support.
Any check or inspection of an anchoring device must be made when the user is safely anchored on another anchoring
device that has been already checked and validated.
This equipment should be operated only by trained, competent and in good health people, or under the supervision of a
trained and competent person.
LV102 Anchorage ring device UPDATE : 14.05.2015 12/104
B.P. 140 - ZAC de La Peyrolière
84405 APT CEDEX - FRANCE