Nice DPRO500 Instructions Et Avertissements Pour L'installation Et L'utilisation page 5

GENERAL WARNINGS: SAFETY - INSTALLATION - USE (original instructions in Italian)
The following warnings are taken directly from the Regulations and apply, as far as possible, to the product described herein
CAUTION Important safety instructions. Follow all instructions as improper installation may cause serious damage
CAUTION Important safety instructions. It is important for you to comply with these instructions for your own and other
people's safety. Keep these instructions
• Before commencing the installation, check the "Product technical specifications", in particular whether this product is suitable for automating
your guided part. If it is not suitable, DO NOT continue with the installation.
• The product cannot be used before it has been commissioned as specified in the chapter on "Testing and commissioning"
CAUTION According to the most recent European legislation, the implementation of an automation system must comply
with the harmonised standards provided by the Machinery Directive in force, which enables declaration of
the presumed conformity of the automation. Taking this into account, all operations regarding connection to
the electricity mains supply, as well as product testing, commissioning and maintenance, must be performed
exclusively by a qualified and skilled technician!
• Before proceeding with the installation of the product, check that all materials are in good working order and suited to the intended applications
• The product is not intended for use by persons (including children) with reduced physical, sensory or mental capacities, nor by anyone with
insufficient experience or familiarity.
• Children must not play with the appliance
• Do not allow children to play with the control devices of the product. Keep the remote controls out of reach of children.
CAUTION In order to avoid any danger from inadvertent resetting of the thermal cut-off device, this appliance must not be
powered through an external switching device, such as a timer, or connected to a supply that is regularly powered
or switched off by the circuit
• Provide a disconnection device (not supplied) in the plant's mains power supply, with a contact opening distance that permits complete
disconnection under the conditions dictated by overvoltage category III
• Handle the product with care during installation, taking care to avoid crushing, denting or dropping it, or allowing contact with liquids of any
kind. Keep the product away from sources of heat and naked flames. Failure to observe the above can damage the product, and increase the
risk of danger or malfunction. If this should happen, stop installation immediately and contact Customer Service.
• The manufacturer assumes no liability for damage to property, items or persons resulting from non-compliance with the assembly instructions.
In such cases the warranty for material defects is excluded
• The weighted sound pressure level of the emission A is lower than 70 dB(A)
• Cleaning and maintenance to be carried out by the user must not be carried out by unsupervised children
• Before working on the system (maintenance, cleaning), always disconnect the product from the mains power supply
• Check the system periodically, in particular all cables, springs and supports to detect possible imbalances, signs of wear or damage. Do not use
if repairs or adjustments are necessary, because a failure with the installation or an incorrectly balanced automated system may lead to injury
• The packing materials of the product must be disposed of in compliance with local regulations
• Keep persons away from the gate when it is moved through the control elements
• When performing a manoeuvre, keep an eye on the automated mechanism and keep all bystanders at a safe distance until the movement
has been completed
• Do not operate the automation if anyone is working on it; disconnect the power supply before permitting any work to be carried out
• If the power cable is damaged, it must be replaced by the manufacturer or by the latter's technical assistance service, or by a similarly qualified
person, in order to prevent any type of risk
• Prior to installing the drive motor, check that all mechanical components are in good working order and properly balanced, and that the au-
tomation moves correctly
• If the gate or door being automated has a pedestrian gate, then the system must include a control device that will inhibit the operation of the
motor when the pedestrian gate is open
• Make sure that the control devices are kept far from moving parts but nonetheless in a visible position.
Unless a selector is used, the control devices must be installed at a height of at least 1.5 m and must not be accessible
Special warnings in relation to European directives applicable to the product
• "Construction Products" Regulation: Special warnings for this product in relation to Regulation 305/2011:
- The full installation of this product, as described in this instruction manual and for certain types of use (e.g. excluding use solely for vehicles)
may cause the product to fall within the scope of Regulation No. 305/2011 and its harmonised standard EN 13241-1.
- It is necessary to apply all the installation criteria to ensure that the product meets the essential requirements of Regulation No. 305/2011;
the installer must check and make sure that all these criteria have been scrupulously complied with.
- The essential requirements might not be guaranteed if the product is installed and used without compliance with one or more of these
criteria. It is forbidden to use the product in such circumstances until the installer has verified compliance with the Directive requirements;
in this case the "ES13241-1.4870" label attached to the product must be removed immediately and the "EC Declaration of Conformity"
(Annex I to this manual) cannot be used. As a result, the installer in turn becomes the manufacturer of the product and must comply with
the provisions of Regulation No. 305/2011 and its harmonised standard EN 13241-1. In this case the product must be considered as
"partly-completed machinery" and the "Declaration of Conformity" of Annex II can be used (for inclusion in the technical documentation).
• "Low Voltage" Directive:
Special warnings regarding the fitness of use of this product in relation to the "Low Voltage" Directive. This product meets the requirements
in the "Low Voltage" Directive, if used for the use and in the configurations specified in this instruction manual and in combination with the
items in the Nice S.p.A. product catalogue.
If the product is used in unspecified configurations or with other unspecified products, the requirements may not be guaranteed; the use
of the product in such circumstances is prohibited until the installer has verified compliance with the specified requirements of the directive.
INSTALLATION PRECAUTIONS
English – 1