Chicco BebeCare oasys Mode D'emploi page 29

4.2 USE AS BABY BOUNCING CHAIR
When the child car seat is not used in a car,
it can be used as a baby bouncing chair.
Place the child car seat only on stable hori-
zontal surfaces.
WARNING! Before carrying the child car seat,
always move the carry handle to position
B (vertical).
WARNING! Never leave your child unat-
tended.
WARNING! Always use the restraint system.
WARNING! Using the child car seat on raised
surfaces such as tables, chairs etc. can be
very dangerous.
WARNING! This child car seat is not designed
for long periods of sleep.
WARNING! Do not use the seat when the
child is able to sit up independently.
This child car seat is not a replacement for a
bed or cot. If children needs to sleep, they
should be moved to a bed or a cot.
Do not use the child seat if any of its parts
are broken or missing.
4.3 USE WITH THE STROLLER
The Oasys 0+ UP car chair seat can be used
with the LOVE, LOVEmotion, LOVE UP – Style-
Go, StyleGo UP.
WARNING! Please read the Stroller instruc-
tion manual when using the child car seat
on the stroller.
Before fastening the child car seat, remove
the stroller seat.
To install the child car seat on the stroller,
proceed as follows:
- Hold the child car seat by moving the
carry handle in vertical position (Fig. 5 -
B) (Fig. 23).
- Fit inside the slots N the relevant devices
on the stroller (Fig. 24A - LOVEmotion UP,
Fig. 24B - StyleGo UP)
making sure the seat is engaged on both
sides. You will hear a CLICK when it is fas-
tened correctly.
WARNING: Before use, make sure that all the
child car seat fastening devices are correctly
engaged.
To remove the child car seat from the stroller:
1. Put the carry handle into vertical position
(Fig. 5 - B).
2. Pull first the rear release handle (Fig. 4 –
P) and then lift the child car seat by the
carry handle (Fig. 25A - LOVEmotion UP,
Fig. 25B - StyleGo UP).
3. Remove and place the child seat on a flat,
stable surface.
WARNING! The child car seat can be fastened
and unfastened with the baby inside; these
procedures could be more difficult due to
the weight of the baby. Be very careful when
performing the steps described above.
4.4 CANOPY
The child car seat features a protective can-
opy in a number of positions.
To fit it, insert the ends of the canopy in the
relevant fastening devices (Fig. 26) and then
fit the elastic strap through the relevant
hooks (Fig. 27). Fasten the buttons on the
back of the canopy to complete fitting (Fig.
28). To remove the hood, press button X (Fig.
26) and pull the ends up.
4.5 CLEANING AND STORAGE
CLEANING THE FABRIC LINING
The child seat's fabric lining can be removed
and washed by hand or in a washing ma-
chine at 30°C.
To wash it, unfasten the straps, remove the
shoulder straps by opening the snap-but-
tons located inside the compartment for
storing the instruction manual (Fig. 29) and
pull off from the straps (Fig. 30). Then re-
move the straps from the slots and the lining
from the headrest (Fig. 31). Remove the fab-
ric lining from the seat starting from the feet
position (Fig. 32), then from the area near the
strap guides (Fig. 33) and finally removing it
completely (Fig. 34).
Follow the steps above in reverse order to
fit the lining again.
WARNING! Fit the straps again correctly and
avoid twisting.
Please refer to the cleaning instructions
on the fabric label, which illustrates the
following washing symbols:
30° C
30° C
29
Machine washable at 30°C.
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean