2�4 Ambient Conditions For Storage And Transport; 2�5 Hazard And Warning Information; 2�5�1 General Information; Specific Information - Renfert Waxlectric I Traduction Du Mode D'emploi D'origine

2.4 Ambient Conditions for Storage and Transport
For storage and transport the following specifications to ambient conditions apply:
• Ambient temperature - 20 – + 60 ºC [- 4 – + 140 ºF]�
EN
• Maximum relative humidity 80 %�
2.5 Hazard and Warning Information
2.5.1 General Information
► If the device is not used in compliance with the supplied instructions, the safety of the device can
no longer be guaranteed.
► The device may only be operated using a mains cable with the country-specific plug system. Any
necessary alterations must be carried out by a qualified electrician.
► The device may only be operated if the information on the identification plate conforms to the
specifications of your local mains power supply. After removing the dust drawer, you can find the
identification plate below, inside the device on the left side.
► The device may only be plugged into outlets which are connected to the protective conductor
system.
► The mains plug must be easily accessible.
► Disconnect the device from the mains before carrying out work on the electrical parts.
► Check connection cables (such as power supply cords), tubes and housing (i.e. the key-pad)
regularly for damage (i.e. kinks, cracks and porosity) or signs of ageing. Devices with damaged
connection cables, tubes or housing parts or other defects must not be operated!
► Defective devices must be put out of service immediately. Remove the mains plug and ensure the
device is not used. Send the device for repair!
► Only operate the device under supervision.
► Please observe the national accident prevention regulations!
► It is the responsibility of the operator that national regulations during operation and regarding
a repeated safety inspection of electrical equipment are complied with. For Germany these are
the regulation 3 by DGUV (German Statutory Accident Insurance) in relation with VDE 0701-0702
(Association for Electrical, Electronic and Information Technology).
► Information on REACH and SVHC is available on our website www.renfert.com, in the Support
area.
2.5.2

Specific Information

► The modelling tips can reach a maximum operating temperature of 200 °C [392 °F].
► While working the tip of the heating handle becomes very hot.
► Incorrect handling presents the risk of burns!
► When setting up and operating please pay attention that the cables do not encounter hot parts.
► Always insert the handpiece with the tip into the holder provided on the control unit in order to
avoid a potential fire hazard.
► NEVER place the handpiece on a flammable surface or cover it! Fire hazard!
► Do not put any combustible or flammable objects close to the unit.
► The wax knife is solely intended for working modelling waxes.
► NEVER hold the wax knife directly in an open flame (e.g., a Bunsen burner)!
► Processing other materials may result in hazards to the user!
► Only intended for indoor use. The unit is only designed for dry applications and may not be oper-
ated or stored outdoors or under wet conditions.
► Do not cover the transformer during operation.
► Protect the transformer against water and moisture.
► Unroll the transformer's connecting cord during operation (a rolled cord represents an overheat-
ing hazard in case of short circuits).
2.6 Authorized Persons
Operation and maintenance of the device may only be performed by qualified personnel. Any repairs not
specifically described in these operating instructions may only be carried out by a qualified electrician.
2.7 Liability Exclusion
Renfert GmbH shall be absolved from all claims for damages or warranty if:
► The product is employed for any purposes other than those cited in the operating instructions;
► The product is altered in any way other than those alterations described in the operating instruc-
tions;
► The product is repaired by other than an authorized facility or if any but Renfert OEM parts are
employed;
► The product continues to be employed, despite obvious safety faults or damage;
► The product is subjected to mechanical impacts or is dropped.
- 4 -