SOUNDMASTER MCD5550 Mode D'emploi page 18

CD programming
Up to 20 tracks can be programmed for disc play in any order. Before use, be sure to press the " stop
Set in CD mode & stop the CD playback.
1.
Press the " Mem/Clk-Adj " button (12) and " MEM " will appear on LCD display (2).
2.
Select a desired track by pressing skip up
3.
Press the " Mem/Clk-Adj " button (12) to store the track into memory.
4.
Repeat steps 3 and 4 to enter additional tracks into the memory if necessary.
5.
When all the desired tracks have been programmed, press " Play/Pause
6.
Press " Stop " button (3) to stop playback, press Stop button again to clear all stored memory.
7.
The programming mode will automatically stop if no button is being pressed in a period of about 10 seconds after pressing
➢
the "Mem/Clk-Adj " button.
Playback of MP3 song via USB storage media or memory card
Connecting
The system is able to decode and playback all MP3 file which stored in the memory media with USB
connecting port or SD memory card.
Set the system at standby mode first or other function except SD or USB mode.
1.
Plug-in the USB pen-drive with the face up & make sure it going into completely or insert the memory
2.
card in the direction of the arrow as shown in the label on the underside of the memory card slot. Insert
straight without bending.
⚫ Connecting the USB upside down or backwards could damage the audio system or the storage media (USB thumb
drive / SD card). Check to be sure the direction is correct before connection.
Set Function button (10) to SD card or USB mode.
3.
The system will start reading the storage media automatically after connecting, and LCD display (2) will show the total
4.
number of MP3 files being detected.
Repeat the same playback procedure and programming as playing CD disc as above.
5.
Remark
The system can detect and read the file under MP3 format only at USB/SD mode but not other music file format.
-
If connect the system to MP3 player via the USB socket, due to variances in MP3 encoding format, some MP3 player
-
may not be able to play via the USB socket. This is not a malfunction of the system.
USB port does not support connection with USB extension cable and is not designed for communication with
-
computer directly
Removing of USB / memory card
To remove the USB / memory card, turn off the power or switch the function mode to either CD, aux or tuner first. For USB port –
un-plug it by pulling out the USB socket directly, for memory card – pull out the SD/MMC card straightly without bending.
Encoding into MP3 file
The system is able to encode normal CD/Tuner/Phono or cassette tape file to MP3 format and recording at memory media with
USB connecting port or SD card and below explanation was encode to USB port and same procedure if encode to SD card. The
system will create a music folder name – " RIP" for CD-DA encode, " REC " for Tuner, Aux, Cassette encode and " FROMCD " for
CD-MP3 disc copy and encode bitrate default at 128kbps.
A) CD encoding
I) encoding 1 track / 1 disc at 1x speed
Perform normal playback of the CD track you want to encode & record,
1.
Press " " button (4) during the playback of the desire track and the display will show "REC" and "USB" flashing.
2.
Press " " button (4) again the display will show "REC" and "ONE" flashing.
3.
Press " " button (4) again, the system will flashing with "REC USB " icon. Encoding is performing now.
4.
After completing of recording, unit will stop playback automatically.
5.
Press " stop " button (3) to interrupt the recording mode anytime.
6.
For encode whole CD track, pls stay CD in stop mode then press "
7.
flashing " REC USB", then system will start to playback CD and encoding whole disc.
or down button (23/13).
6
MCD5550 / English Instruction Manual
" button (3).
" button (16) to play the disc in assigned order.
" button (4) three times until the display