Setting The Hardness Of Blended Water - resideo Braukmann KaltecSoft Instructions D'installation

4.2 Operation
Charge Bar:
Having set the display on the control facia, you will notice that
during normal operation there is a charge bar running along
the bottom of the display.
This charge bar shows the percentage of water softener
capacity remaining since the last regeneration.
Immediately following a regeneration, the charge bar returns
to 100 %.
Resetting the display during operation:
If the time (or any other user setting) is to be adjusted during
normal operation, press any key to illuminate the display,
press the [SET] key once.
The display will flash and indicate present time.
Using the keys will alter the time as described in chapter .
Power loss:
The AMECS system will maintain the individual programming
parameters of the water softener for a few hours.
If the power cut lasts longer than a few hours, the control will
flash "00:00" when power is returned to the control.
The unit will continue to keep time from the moment power is
restored.
In this situation the time of day will need to be reset.
Flow indicator:
During normal operation, a flow indicator will flash on the
display at a rate of one litre per pulse when water is passing
through the softener.
Cleaning:
Your water softener may be cleaned using a damp cloth and
a mild detergent.
Do not use bleaches, solvents or spirits as they may damage
the surfaces.
Manual regeneration [recharge] button:
Under normal operating conditions your water softener will
regenerate automatically and you should not normally have to
regenerate the unit manually.
If however a manual regeneration is required then follow the
procedure set out below.
1. Press any key to illuminate the display
2. Momentarily pressing the recharge button (symbol
underneath the display and furthest to the right) will
illuminate Recharge Tonight on the display and
perform a regeneration at 2.00 a.m. regardless of the
remaining water softener capacity
3. If the recharge button is subsequently pressed, this
will clear the Recharge Tonight indicator from the
display and cancel the Recharge Tonight feature
4. If the recharge button is pressed down for six
seconds, the controller will flash the Recharge display
and immediately commence the regeneration cycle
which cannot be cancelled
GB
Adding regenerative salt:
Refill the salt not later than the current filling is 15 cm above
the base of the salt storage container.
Open the cover (see chapter 1.5 No. 1). Pour regenerative
salt into the storage area.
Refill the unit in such a way that no dirt can get into the salt
container (if necessary, clean the packages containing the
salt before use).
Clean the salt container (3) or brine system (16) with clean
water if it gets dirty.
Salt usage:
Your water softener is controlled by a microprocessor which
constantly monitors water usage.
The system will build up a history of your water requirements
and calculate the most economical regeneration pattern.
This will ensure a constant supply of softened water whilst
maintaining high levels of water and salt efficiency.
As your water softener uses a proportional brining system,
more frequent regenerations do not necessarily mean high
water / salt usage.
Increase in number or residents:
Sudden changes in your water usage should not affect your
water softeners performance.
If however, the number of guests staying with you increases,
you will notice that the water usage patterns will alter.
This may cause your water softener to regenerate more often
than normal.
As the water usage returns to its normal level, the number of
regenerations will also return to normal.
Cabinet Water Level:
During normal operation the water level inside the water
softener cabinet will rise and fall as required by the
regeneration process.
If the water softener is used within the specified
operationalparameters the water level should not reach the
overflow connection.
If however an overflow situation occurs please refer to the
troubleshooting section (chapter 6) to diagnose the problem.
Following any overflow situation reduce the water level and
initiate a manual regeneration as described above.
Check the water level weekly and following any
unplanned event, e.g. powerfailure.
4.3 Setting the hardness of blended
water
After the initial set-up the softener and entering the supply
water hardness, test the outcoming, treated water hardness
downstream from the softener, on one of the nearest cold
water tap by using the water hardness tester.
Adjust with the blending valve (Chapter 3.5 - Nr.3) until the
desired value is reached.
10 MU1H-1420 GE23 R0420