Table Des Matières - Stanley 07536 Manuel D'instructions Et D'entretien

O R I G I N A L I N S T R U C T I O N
©2021 Stanley Black & Decker inc.
All rights reserved.
The information provided may not be reproduced and/or made public in any way and through any means (electronically or
mechanically) without prior explicit and written permission from STANLEY Engineered Fastening. The information provided
is based on the data known at the moment of the introduction of this product. STANLEY Engineered Fastening pursues a
policy of continuous product improvement and therefore the products may be subject to change. The information provided
is applicable to the product as delivered by STANLEY Engineered Fastening. Therefore, STANLEY Engineered Fastening
cannot be held liable for any damage resulting from deviations from the original specifications of the product.
The information available has been composed with the utmost care. However, STANLEY Engineered Fastening will not
accept any liability with respect to any faults in the information nor for the consequences thereof. STANLEY Engineered
Fastening will not accept any liability for damage resulting from activities carried out by third parties. The working names,
trade names, registered trademarks, etc. used by STANLEY Engineered Fastening should not be considered as being free,
pursuant to the legislation with respect to the protection of trade marks.
1. SAFETY DEFINITIONS ................................................................................................................................................... 4
1.1 GENERAL SAFETY RULES .......................................................................................................................................................................... 4
1.2 PROJECTILE HAZARDS .............................................................................................................................................................................. 4
1.3 OPERATING HAZARDS ............................................................................................................................................................................... 5
1.4 REPETITIVE MOTIONS HAZARDS............................................................................................................................................................ 5
1.5 ACCESSORY HAZARDS .............................................................................................................................................................................. 5
1.6 WORKPLACE HAZARDS ............................................................................................................................................................................. 5
1.7 NOISE HAZARDS .......................................................................................................................................................................................... 5
1.8 VIBRATION HAZARDS................................................................................................................................................................................. 5
1.9 ADDITIONAL SAFETY INSTRUCTIONS FOR PNUEMATIC AND HYDRAULIC TOOLS .............................................................. 6
2. SPECIFICATIONS ............................................................................................................................................................ 7
2.1 SPECIFICATION FOR 07536 TOOL .......................................................................................................................................................... 7
2.2 SPECIFICATION FOR 07531 INTENSIFIER ............................................................................................................................................. 7
3. INTENT OF USE .............................................................................................................................................................. 8
3.1 TOOL DIMENSIONS - 07536 MODEL ..................................................................................................................................................... 8
4. PUTTING INTO SERVICE ................................................................................................................................................ 9
4.1 AIR SUPPLY .................................................................................................................................................................................................... 9
4.2 AIR CURSORS ..............................................................................................................................................................................................10
4.3 LOADING AND RELOADING THE TOOL ..............................................................................................................................................10
4.4 OPERATING PROCEDURE ........................................................................................................................................................................12
5. SERVICING THE TOOL.................................................................................................................................................. 13
5.1 PNEUMATIC CONTROL BOX ...................................................................................................................................................................13
5.2 DAILY .............................................................................................................................................................................................................13
5.3 WEEKLY .........................................................................................................................................................................................................13
5.4 MOLY LITHIUM GREASE EP 3753 SAFETY DATA..............................................................................................................................13
5.5 SERVICE KIT ..................................................................................................................................................................................................14
5.6 AIR CURSOR TOOL, INTENSIFIER & CONTROL BOX ASSEMBLY 07536-02100 ......................................................................15
6. MAINTENANCE ............................................................................................................................................................ 16
6.1 DISMANTLING 07536-02200 .................................................................................................................................................................16
6.2 GENERAL ASSEMBLY OF BASE TOOL 07536-02200 .......................................................................................................................18
6.3 PARTS LIST FOR BASE TOOL 07536-02200 .......................................................................................................................................19
6.4 DISMANTLING INSTRUCTIONS .............................................................................................................................................................20
6.5 PROTECTING THE ENVIRONMENT .......................................................................................................................................................21
6.6 INTENSIFIER 07531-02200 ......................................................................................................................................................................21
7. PRIMING ...................................................................................................................................................................... 23
7.1 OIL DETAILS .................................................................................................................................................................................................23
7.2 HYSPIN® VG32 AND AWS 32 OIL SAFETY DATA ..............................................................................................................................23
7.3 PRIMING PROCEDURE..............................................................................................................................................................................23
8. FAULT DIAGNOSIS ....................................................................................................................................................... 24
9. EC DECLARATION OF CONFORMITY .......................................................................................................................... 26
10. UK DECLARATION OF CONFORMITY ......................................................................................................................... 27
11. PROTECT YOUR INVESTMENT! ................................................................................................................................... 28
E N G L I S H
3