Technical specifications:
Engine output:
Connection:
Bandsaw blade speed:
Bandsaw blade length:
Bandsaw blade pulleys:
Max. clear height:
Max. clear width:
Table size:
Weight:
General safety instructions
The Operating Instructions must be read
thoroughly before using the machine for the first time.
If there are any doubts regarding the machine
connection, please contact the manufacturer (service
department).
TO ENSURE HIGH SAFETY LEVEL, PLEASE FOLLOW
CAREFULLY THESE INSTRUCTIONS:
CAUTION!
•
Keep the place of your work clean and tidy. Mess
in the place of your work and work-table increases
the risk of accidents and injuries.
•
Consider carefully the conditions of the
environment you are working in. Do not use any
electric tools and machine tools in a wet and moist
environment. Provide adequate lighting. Do not
expose any electric tools to rain or high air humidity.
Do not switch electric tools on near highly flammable
liquids and gases.
•
Do not let other persons get near the machine.
Keep all visitors and bystanders, especially children
and ill or weak persons, in a safe distance from the
place of your work.
•
Make sure tools are kept safe. Keep any tools you
are not using in a dry place, elevated if possible, or
lock them to prevent other persons accessing them.
•
Use the right machine for your work. Do not use
e.g. small tools or accessory equipment for works that
actually need to be performed by big tools. Use the
machine only for purposes for which it has been
designed. Do not overload your machine!
•
Look out for the feeder cable. Do not pull the cable.
Do not use the cable to unplug the machine. Keep the
cable out of reach of heat sources, oil and sharp
edges.
•
Avoid any unintentional switching-on. Before
plugging the machine, make always sure the machine
is switched off.
•
Special extension cables to be used outdoors. To
use the machine outdoors, special extension cables
appropriate for that purpose and adequately labelled
must be used.
•
Be cautious at all times. Pay attention to what you
are doing. Use common sense when working. Do not
use any electric tools when you are tired.
•
Watch for any worn parts. Inspect the machine
before using it. Are any parts damaged? In case of
slight damage, consider seriously whether the
machine can work perfectly and safely.
•
Prevent electric shock. Avoid any physical contact
with grounded items, e.g. water pipes, heating units,
cookers and fridges.
•
Approved parts to be used only. Identical spare
parts to be used only for any servicing or repair. For
that purpose, contact an authorised service centre.
•
Caution! Using accessory equipment and extensions
not explicitly recommended in these Operating
Instructions may pose a risk to persons and property.
•
Do not incline from the place of your work
Avoid any abnormal body posture. Provide safe
posture and keep balance at all times.
•
Do not leave any adjusting wrench in the machine
Before starting the machine, check whether
adjustment wrenches and tools have been removed.
250 W S2 15 min
230V~50Hz
15.7 m per second
1,400 mm
205 mm
80 mm
190 mm
300 x 300 mm
app. 20 kg
Machine-specific safety instructions
Learn your machine using the Operating Instructions
•
Protection covers must not be removed
•
Before starting the machine, remove any adjustment
wrenches and tools
•
Keep the place of your work clean
•
Keep children and bystanders in a safe distance from
the place of your work
•
Do not overload your machine
•
Use the right machine with no defects
•
Wear appropriate closefitting clothes
•
Wear protective glasses
•
Hold the cut material properly
•
Never leave the machine unattended
•
The machine must not be used after you have
consumed any drugs, alcohol or pharmaceuticals.
Additional safety instructions for using band saws:
•
Adjust the bandsaw blade guide so that it protrudes
not more than 3 mm above the highest edge of the
cut material
•
Keep your fingers and hands in a safe distance from
the bandsaw blade
•
To move the cut material, use appropriate accessory
•
Switch the machine off first and then remove any
cuttings off the table
•
Setting and adjusting to be performed only when the
machine is unplugged
•
Protection covers of the band saw must not be
removed
•
All adjusting elements must be secured against any
unintentional adjustment change
•
Hold the cut material safely and work with balanced
pressure
•
Approved bandsaw blades to be used only.
Noise may reach a level of 80 dB(A) when the machine
is being operated, therefore you should wear earmuffs.
Behaviour in case of emergency
First aid kit must always be available in the place of your
work in case of accident in accordance with DIN 13164.
Material taken out of the first aid kit needs to be
supplemented right away.
If help is needed, please provide the following details:
Place of accident
Accident nature
Number of injured persons
Injury type
Provide necessary first aid treatment corresponding to the
injury nature and seek qualified medical help as soon as
possible. Protect the injured person from other injuries and
calm him/her down.
Disposal
The disposal instructions are based on icons placed on the
machine or on its package. The description of the
meanings can be found in the "Marking" section.
Transport container disposal
The container protects the machine against damage during
transport. Container materials are usually selected based
on their environment friendliness and disposal method and
can therefore be recycled. Returning the container back to
circulation saves raw materials and reduces waste
disposal costs. Parts of the container (e.g. foils, styropor)
can be dangerous to children. Risk of suffocation!
Keep parts of the container out of reach of children and
dispose them as quickly as possible.
9