Makita DSL800 Manuel D'instructions page 16

Push the wireless activation button on the tool
4.
briefly. The wireless activation lamp will blink in blue.
Fig.32: 1. Wireless activation button 2. W ireless
a c ti v ation lamp
5. P ull t h e s w it c h trigger o f t h e tool. C h e c k i f t h e
vacuum cleaner runs while the switch trigger is being
pulle d .
T o stop t h e w ireless a c ti v ation o f t h e v a c uum c leaner,
push the wireless activation button on the tool.
Description of the wireless activation lamp status
Fig.33: 1. W ireless a c ti v ation lamp
The wireless activation lamp shows the status of the wireless activation function. Refer to the table below for the
meaning o f t h e lamp status.
Status
Color
Standby
Blue
T ool G reen
registration
C anc elling R ed
tool
registration
O th ers R ed
O f f
Cancelling tool registration for the
vacuum cleaner
P er f orm t h e f ollo w ing pro c e d ure w h en c an c elling t h e
tool registration f or t h e v a c uum c leaner.
Install the batteries to the vacuum cleaner and the
1.
tool.
Set the stand-by switch on the vacuum cleaner to
2.
AUTO .
Fig.34: 1. Stand-by switch
Press the wireless activation button on the vac-
3.
uum cleaner for seconds. The wireless activation
lamp blinks in green and then become red. After that,
press the wireless activation button on the tool in the
same way.
Fig.35: 1. Wireless activation button 2. W ireless
a c ti v ation lamp
W ireless activation lamp
On Blinking
20 sec ond s Ready for the tool registration. Waiting for the registration by the
20 sec ond s Ready for the cancellation of the tool registration. Waiting for the
-
NOTE: T h e w ireless a c ti v ation lamp on t h e tool w ill
stop blinking in blue when there is no operation for
hours. In this case, set the stand-by switch on the
vacuum cleaner to AUTO and push the wireless
activation button on the tool again.
NOTE: The vacuum cleaner starts/stops with a delay.
T h ere is a time lag w h en t h e v a c uum c leaner d ete c ts
a s w it c h operation o f t h e tool.
NOTE: T h e transmission d istan c e o f t h e w ireless unit
may vary depending on the location and surrounding
c ir c umstan c es.
NOTE: W h en t w o or more tools are registere d to one
vacuum cleaner, the vacuum cleaner may start run-
ning even if you don t pull the switch trigger because
anot h er user is using t h e w ireless a c ti v ation f un c tion.
Duration
The wireless activation of the vacuum cleaner is available. The
2 h ours
lamp will automatically turn off when no operation is performed
f or 2 h ours.
The wireless activation of the vacuum cleaner is available and the
W h en
th e tool is tool is running.
running.
v ac uum c leaner.
The tool registration has been finished. The wireless activation
2 sec ond s
lamp will start blinking in blue.
cancellation by the vacuum cleaner.
The cancellation of the tool registration has been finished. The
2 sec ond s
wireless activation lamp will start blinking in blue.
3 sec ond s T h e pow er is supplied to th e w ireless unit and th e w ireless ac tiv a-
tion f unc tion is starting up.
- T h e w ireless ac tiv ation of th e v ac uum c leaner is stopped .
If the cancellation is performed successfully, the wire-
less a c ti v ation lamps w ill lig h t up in re d f or 2 se c on d s
and start blinking in blue.
NOTE: The wireless activation lamps finish blinking in
re d a f ter 20 se c on d s elapse d . P ress t h e w ireless a c ti-
vation button on the tool while the wireless activation
lamp on the cleaner is blinking. If the wireless acti-
vation lamp does not blink in red, push the wireless
activation button briefly and hold it down again.
16 ENGLISH
Description