Makita DSL800 Manuel D'instructions page 15

W IRELESS ACTIVATION
FUNCTION
Optional accessory
W hat you can do with the wireless
activation function
The wireless activation function enables clean and com-
fortable operation. By connecting a supported vacuum
cleaner to the tool, you can run the vacuum cleaner
automatically along with the switch operation of the tool.
Fig.24
T o use t h e w ireless a c ti v ation f un c tion, prepare f ollo w -
ing items:
A wireless unit (optional accessory)
A vacuum cleaner which supports the wireless
a c ti v ation f un c tion
T h e o v er v ie w o f t h e w ireless a c ti v ation f un c tion
setting is as f ollo w s. R e f er to ea c h se c tion f or d etail
pro c e d ures.
1. I nstalling t h e w ireless unit
2. T ool registration f or t h e v a c uum c leaner
3. S tarting t h e w ireless a c ti v ation f un c tion
Installing the wireless unit
Optional accessory
Place the tool on a at and stable
CAUTION:
surface when installing the wireless unit.
NOTICE:
Clean the dust and dirt on the tool before
installing the wireless unit. Dust or dirt may cause
mal f un c tion i f it c omes into t h e slot o f t h e w ireless unit.
NOTICE:
To prevent the malfunction caused by static,
touch a static discharging material, such as a metal part
of the tool, before picking up the wireless unit.
NOTICE:
W hen installing the wireless unit, always
be sure that the wireless unit is inserted in the cor-
rect direction and the lid is completely closed.
Open the lid on the tool as shown in the figure.
1.
Fig.25: 1. L i d
2. I nsert t h e w ireless unit to t h e slot an d t h en c lose t h e li d .
When inserting the wireless unit, align the projections
w it h t h e re c esse d portions on t h e slot.
Fig.26: 1. W ireless unit 2. Projection 3. L i d
4. R e c esse d portion
When removing the wireless unit, open the lid slowly.
The hooks on the back of the lid will lift the wireless unit
as you pull up the lid.
Fig.27: 1. W ireless unit 2. H ook 3. L i d
After removing the wireless unit, keep it in the supplied
c ase or a stati c - f ree c ontainer.
NOTICE:
Always use the hooks on the back of
the lid when removing the wireless unit. I f t h e
h ooks d o not c at c h t h e w ireless unit, c lose t h e li d
completely and open it slowly again.
Tool registration for the vacuum
cleaner
NOTE: A Makita vacuum cleaner supporting the
wireless activation function is required for the tool
registration.
NOTE: Finish installing the wireless unit to the tool
before starting the tool registration.
NOTE: D uring t h e tool registration, d o not pull t h e
s w it c h trigger or turn on t h e po w er s w it c h on t h e
v a c uum c leaner.
NOTE: R e f er to t h e instru c tion manual o f t h e v a c uum
c leaner, too.
If you wish to activate the vacuum cleaner along with
the switch operation of the tool, finish the tool registra-
tion beforehand.
Install the batteries to the vacuum cleaner and the
1.
tool.
Set the stand-by switch on the vacuum cleaner to
2.
AUTO .
Fig.28: 1. Stand-by switch
Press the wireless activation button on the vac-
3.
uum c leaner f or 3 se c on d s until t h e w ireless a c ti v ation
lamp blinks in green. And then press the wireless acti-
vation button on the tool in the same way.
Fig.2 9 : 1. Wireless activation button 2. W ireless
a c ti v ation lamp
I f t h e v a c uum c leaner an d t h e tool are linke d su c c ess-
fully, the wireless activation lamps will light up in green
for seconds and start blinking in blue.
NOTE: The wireless activation lamps finish blinking
in green a f ter 20 se c on d s elapse d . P ress t h e w ireless
activation button on the tool while the wireless acti-
vation lamp on the cleaner is blinking. If the wireless
activation lamp does not blink in green, push the wire-
less activation button briefly and hold it down again.
NOTE: W h en per f orming t w o or more tool registra-
tions for one vacuum cleaner, finish the tool registra-
tion one by one.
Starting the wireless activation
function
NOTE: Finish the tool registration for the vacuum
c leaner prior to t h e w ireless a c ti v ation.
NOTE: R e f er to t h e instru c tion manual o f t h e v a c uum
c leaner, too.
After registering a tool to the vacuum cleaner, the
vacuum cleaner will automatically runs along with the
s w it c h operation o f t h e tool.
1. I nstall t h e w ireless unit to t h e tool.
2. C onne c t t h e h ose o f t h e v a c uum c leaner w it h t h e
tool.
Fig.30
Set the stand-by switch on the vacuum cleaner to
3.
AUTO .
Fig.31: 1. Stand-by switch
15 ENGLISH