Makita DSL800 Manuel D'instructions page 17

Troubleshooting for wireless activation function
Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual,
do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace-
ment parts f or repairs.
State of abnormality
T h e w ireless ac tiv ation lamp d oes
not light/blink.
Cannot finish tool registration / can-
celling tool registration successfully.
T h e v ac uum c leaner d oes not run
along w ith th e sw itc h operation of
th e tool.
T h e v ac uum c leaner runs w h ile th e
tool s switch trigger is not pulled.
Probable cause (malfunction)
T h e w ireless unit is not installe d into t h e tool.
The wireless unit is improperly installed
into th e tool.
The terminal of the wireless unit and/or
the slot is dirty.
The wireless activation button on the
tool has not been pushed.
The stand-by switch on the vacuum
cleaner is not set to AUTO .
No power supply
T h e w ireless unit is not installe d into t h e tool.
The wireless unit is improperly installed
into th e tool.
The terminal of the wireless unit and/or
the slot is dirty.
The stand-by switch on the vacuum
cleaner is not set to AUTO .
No power supply
I nc orrec t operation
The tool and vacuum cleaner are away
f rom eac h oth er ( out of th e transmission
range) .
Before finishing the tool registration/
c anc ellation;
- th e sw itc h trigger on th e tool is pulled or;
- the power button on the vacuum
c leaner is turned on.
T h e tool registration pro c e d ures f or t h e
tool or vacuum cleaner have not finished.
Radio disturbance by other appliances
which generate high-intensity radio
w av es.
T h e w ireless unit is not installe d into t h e tool.
The wireless unit is improperly installed
into th e tool.
The terminal of the wireless unit and/or
the slot is dirty.
The wireless activation button on the
tool has not been pushed.
The stand-by switch on the vacuum
cleaner is not set to AUTO .
More th an 1 0 tools are registered to th e
v ac uum c leaner.
T h e v ac uum c leaner erased all tool
registrations.
No power supply
The tool and vacuum cleaner are away
f rom eac h oth er ( out of th e transmission
range) .
Radio disturbance by other appliances
which generate high-intensity radio waves.
O th er users are using th e w ireless
ac tiv ation of th e v ac uum c leaner w ith
th eir tools.
17 ENGLISH
Remedy
Install the wireless unit correctly.
Gently wipe off dust and dirt on the terminal of the
w ireless unit and c lean th e slot.
Push the wireless activation button on the tool
briefly.
Set the stand-by switch on the vacuum cleaner to
AUTO .
Supply the power to the tool and the vacuum cleaner.
Install the wireless unit correctly.
Gently wipe off dust and dirt on the terminal of the
w ireless unit and c lean th e slot.
Set the stand-by switch on the vacuum cleaner to
AUTO .
Supply the power to the tool and the vacuum cleaner.
Push the wireless activation button briefly and perform
the tool registration/cancellation procedures again.
G et th e tool and v ac uum c leaner c loser to eac h
oth er. T h e max imum transmission d istanc e is
approximately m however it may vary according
to th e c irc umstanc es.
Push the wireless activation button briefly and
perform the tool registration/cancellation procedures
again.
Perform the tool registration procedures for both the
tool and th e v ac uum c leaner at th e same timing.
Keep the tool and vacuum cleaner away from the
appliances such as Wi-Fi devices and microwave
ov ens.
Install the wireless unit correctly.
Gently wipe off dust and dirt on the terminal of the
w ireless unit and c lean th e slot.
Push the wireless activation button briefly and make
sure that the wireless activation lamp is blinking in blue.
Set the stand-by switch on the vacuum cleaner to
AUTO .
P erf orm th e tool registration again.
I f more th an 1 0 tools are registered to th e v ac uum c leaner,
the tool registered earliest will be cancelled automatically.
P erf orm th e tool registration again.
Supply the power to the tool and the vacuum cleaner.
G et t h e tool an d v a c uum c leaner c loser ea c h ot h er. T h e
maximum transmission distance is approximately
however it may vary according to the circumstances.
Keep the tool and vacuum cleaner away from the appli-
ances such as Wi-Fi devices and microwave ovens.
Turn off the wireless activation button of the other
tools or c anc el th e tool registration of th e oth er
tools.
m