Assembly Components; Steering Wheel - Mountfield 2135H Mode D'emploi

EN
3 ASSEMBLY
To avoid injury and damage to people
and property, do not use the machine
until all the measures under
"ASSEMBLY" have been carried out.

3.1 ASSEMBLY COMPONENTS

Components that are to be used at assembly are
included in the delivery. See fig. 1.
Supplied in bag:
Pos No. Designation
A 1 Towing plate
B 2 Screw with flange 8 x 20
C 2 Screw for battery
D 2 Nut for battery
E 4 Washer
F 2 Shoulder washer
G 4 Screw
H 2 Screw knob
I 2 Ignition key
J 1 Tension pin
K 1 Shim washer
L 1 Shim washer
P 2 Screw
Q 2 Nut
Supplied installed on the front axles:
Pos No. Designation
M 2 Circlip
N 2 Washer with internal lug
Secured to the implement lifter:
Pos No. Designation
O 2 Deck mount
3.2 ENGINE CASING
To fill with fuel and to inspect and maintain the
engine and battery, open the engine casing.
The engine must not be running when
the casing is opened.
3.2.1 Opening
1. Ensure that the control arms are in their forward
positions.
2. Raise the seat lock (2:S) and fold the seat
forwards.
3. Grasp the front edge of the engine casing and
fold up the casing (fig. 3).
3.2.2 Closing
Grasp the front edge of the engine casing and fold
down the casing (fig. 3).
The machine may not be operated
unless the engine casing is folded down.
Risk of burns and crushing injuries.
8
All manuals and user guides at all-guides.com
ENGLISH
3.3 BATTERY
See "7.7 Battery".
3.4 SEAT
NOTE! To facilitate installation of the seat,
apply a drop of oil to the four screws before
screwing them into the seat.
Release the catch (2:S) and fold up the seat
bracket.
Install the mounting in the rear (upper) holes as
follows:
1. Install the shoulder washers (2:F) on the screws
Dimension
2. Insert the screws through the slots in the
3. Tighten the screws in the seat. Tightening
8.4 x 24 x 2.0
8 x 20
4. Check that the seat moves easily in the slots in
6 x 36
16 x 38 x 0.5
Install the mounting in the front (lower) holes as
follows:
16 x 38 x 1.0
M10 x 35 1. Install the screw knobs (2:H) on the screws
M10
2. Install a washer (2:I) on each screw.
3. Insert the screws through the slots in the bracket
4. Fold the seat down and place it in the desired
5. Tighten the screw knobs (2:H) by hand.
The seat can be folded. If the machine is parked
outside when it is raining, fold the seat forward to
protect the seat cushion from getting wet.
The seat is locked. To fold the seat up or down,
release the catch (2:S).

3.5 STEERING WHEEL

In order to minimise the axial play in the steering
column, the shim washers (4:K) and/or (4:L) must
be installed on the steering column between the
steering column jacket and the bracket as follows.
1. Install the steering column jacket on the
2. Pull the steering column jacket and the steering
Original instructions for use
(2:G).
bracket. Place a washer (2:I) between the seat
and the bracket.
torque: 9±1.7 Nm.
If the screws are tightened more than
9±1.7 Nm, the seat will be damaged.
the bracket.
(2:G).
and tighten by hand in the seat.
position.
The screw knobs (2:H) and the seat will
be damaged if tools are used.
steering column and secure by knocking in the
cotter pin (4:K) approximately 1/3 of its length.
column up.