Section 10 - Maintenance Et Dépannage; Entretien Courant - Miller Dynasty 280 Serie Manuel De L'utilisateur

SECTION 10 – MAINTENANCE ET DÉPANNAGE

10-1. Entretien courant

A. Poste de soudage
SECTION 12
SECTION 6
SECTION 6
12-1. Routine Maintenance
Tous les
Every
Every
3 mois
3
3
Months
Months
Labels
Labels
� � Étiquettes
Every
Every
A. Welding Power Source
3
3
Months
Months
SECTION 9
Every
3
Months
!
Do not remove case when blowing out inside of unit
� � Câbles et cordons
6-1. Blowing Out Inside of Unit
6-1. Blowing Out Inside of Unit
Tous les
Every
3
6 mois
Months
� en cas d'utilisation intensive, nettoyer tous les mois.
:During heavy service, clean monthly. Every
6
Ne pas enlever le capot lors du nettoyage par jet d'air de l'intérieur de l'appareil.
Months
B. Refroidisseur en option
= Check
* To be done by Factory Authorized Service Agent
Tous les
3 mois
B. Optional Cooler
durning heavy service,
clean more frequently.
Every
3
� Filtre de liquide de refroidissement ; en cas d'utilisation inten-
Months
sive, nettoyer plus souvent.
Tous les
Every
6 mois
6
Months
� � Flexibles
Every
Tous les
12
12 mois
Months
◇ Liquide de refroidissement.
OM-253086 Page 60
�
Une liste complète de pièces détachées est disponible sur www.MillerWelds.com
A complete Parts List is available at www.MillerWelds.com
A complete Parts List is available at www.MillerWelds.com
A complete Parts List is available at www.MillerWelds.com
MAINTENANCE AND TROUBLESHOOTING
MAINTENANCE AND TROUBLESHOOTING
MAINTENANCE AND TROUBLESHOOTING
� = Vérifier
� � Tuyaux de gaz
A complete Parts List is available at www.MillerWelds.com
= Check = Change
MAINTENANCE AND TROUBLESHOOTING SECTION 9
* To be done by Factory Authorized Service Agent
Every
!
Do not remove case when blowing out inside of unit
6
Labels Gas Hoses
Months
Cables And Cords
:During heavy service, clean monthly.
!
Do not remove case when blowing out inside of unit
9-1.Optional Cooler
� = Vérifier
= Change = Check = Clean
* To be done by Factory Authorized Service Agent
:During heavy service, clean monthly.
Every
3
Coolant Strainer,
Months
= Check = Change
* To be done by Factory Authorized Service Agent
Coolant Strainer,
durning heavy service,
clean more frequently.
9-2. Blowing Out Inside of Unit
Hoses
Débrancher l'alimentation avant d'effectuer des tra-
vaux d'entretien.
�
Augmenter la fréquence des travaux d'entretien dans des
conditions sévères.
◇ = Modifier
!
Disconnect power before maintaining.
Maintain more often during severe conditions.
A complete Parts List is available at www.MillerWelds.com
SECTION 9 MAINTENANCE AND TROUBLESHOOTING
Every
!
Do not remove case when blowing out inside of unit
6
A complete Parts List is available at www.MillerWelds.com
Months
= Clean = Repair
MAINTENANCE AND TROUBLESHOOTING
:During heavy service, clean monthly.
9-1.Optional Cooler
= Check = Change = Clean = Repair
* To be done by Factory Authorized Service Agent
Every
3
Blow out heat exchanger fins.
Coolant Strainer,
Months
Check coolant level. Top off with
durning heavy service,
distilled or deionized water if necessary.
clean more frequently.
9-2. Blowing Out Inside of Unit
◇ = Modifier
= Change = Repair = Clean
OM-270536 Page 42
Blow out heat exchanger fins.
Coolant Strainer,
Check coolant level. Top off with
durning heavy service,
clean more frequently.
= Clean = Repair
Blow out heat exchanger fins.
� Nettoyer les ailettes du radiateur par jet d'air.
Check coolant level. Top off with
� Vérifier le niveau du liquide de refroidissement. Si nécessaire,
distilled or deionized water if necessary.
faire l'appoint d'eau distillée ou dé-ionisée.
Labels
�� Étiquettes
� = Nettoyer
Weld Terminals
Weld Terminals
= Replace
= Replace
! Do not remove case when
blowing out inside of unit.
To blow out unit, direct airflow
through front and back louvers as
shown.
805497-A
� = Nettoyer
= Replace = Repair
Blow out heat exchanger fins.
Check coolant level. Top off with
distilled or deionized water if necessary.
= Replace
!
Do not remove case when
blowing out inside of unit.
To blow out unit, direct airflow
through front and back louvers as
shown.
OM-270536 Page 65
� = Remplacer
� = Remplacer
= Replace
!
Do not remove case whe
blowing out inside of unit.
OM-249336 Page 1
To blow out unit, direct airflo
through front and back louvers a
shown.
804746-B
804746-B
805497-A 805497