steute RF 96 ST SW868 Instructions De Montage Et De Câblage page 3

RF 96 ST SW868/SW915/SW917/SW922
//
Montage- und Anschlussanleitung / Funkschalter
Mounting and wiring instructions / Wireless switch
Instructions de montage et de câblage / Interrupteur sans fil
Istruzioni di montaggio e collegamento / Interruttore wireless
Instruções de montagem e instalação / Interruptor de rádio frequência
Инструкция по монтажу и подключению / Радио-выключатель
English
Use of the mounting and wiring instructions
Target group: authorised and qualified staff.
All actions described in these instructions may only be performed by
qualified persons who have been trained and authorised by the
operating company.
1. Read and understand these mounting and wiring instructions.
2. Comply with the valid occupational safety and accident prevention
regulations.
3. Install and operate the device.
Selection and installation of devices and their integration in control
systems demand qualified knowledge of all the relevant laws, as well
as the normative requirements of the machine manufacturer. In case
of doubt, the German language version of these instructions shall
prevail.
Scope of delivery
1 device, 1 mounting and wiring instructions, carton.
Intended use
The device essentially comprises three parts: the power supply with
a lithium battery, the wireless part with an integrated interface for the
external sensors and the connecting part for the external sensors.
The power supply is provided by a non-rechargeable 3.6 V lithium thio-
nylchloride battery and a nominal capacity of 8.5 Ah. Exceeding the
threshold triggers a wireless signal. The battery status is transmitted
with every signal transmission. The receiver must conform to the
sWave ® protocol of the steute modules.
Mounting and wiring
Mount the device on an even surface. Install the device according to
the mounting and wiring instructions of the receiver. The wireless
range depends heavily on the local conditions. Conductive materials
may strongly affect the radio signal. This also includes thin foils, e.g.
aluminium laminations on insulation materials.
Allocation of locations and radio frequencies:
Device type Radio frequency
SW868 868.3 MHz
SW915 915.0 MHz
SW917 917.0 MHz
SW922 916.5 MHz
Place of use according to
EU 2014/53/EU (RED)
USA FCC
Canada IC
Mexico IFT
Brazil ANATEL
Japan ARIB STD-T108
External devices
The sensor/switch connection is evident at the M12 plug-in connector.
At this plug-in connector the inductive sensors RF IS M8/M12/M18- or
M30 or other mechanical switches with gold-plated contacts can be
connected. Therefore, the connecting cable Material No. 1189960 can
be used that is avai-lable as accessory. The mechanical switches must
be equipped with a NO/NC contact. It must be connected to plus (pin 1)
and to the entry (pin 4). To connect external devices (sensors or
switches): see section »Connecting external devices«. When installing
the external device, follow its installation instructions.
Connectable devices:
Device
0.3 m
RF IS M8 nb-ST
RF IS M12 nb-ST
RF IS M18 nb-ST
RF IS M30 nb-ST
RF RC 20 1S-ST 1335490
connecting cable,
open wire ends
Design of wireless range
The radio signal is attenuated on the way from the transmitter to
the receiver. In addition, the radio signal is attenuated/influenced by
obstacles. The degree of attenuation depends on the material of the
obstacle. The following tables serve as a guide.
Penetration of radio signals:
Material
wood, gypsum, glas uncoated
brick stone, press boards
armoured concrete
metal, aluminium lamination, water
Typical ranges:
Place of use
in free field (SW868/915/917)
in free field (SW922)
indoors (SW868/915/917)
indoors (SW922)
3 / 20
Material No. (Cable length)
0.5 m 1 m 2 m
1470040 1373082 1305745
1228522 1356467 1189974
1261564 on request 1189975
1260490 1228548 1189976
1215497
Penetration
90...100%
65...95%
10...90%
0...10%
Wireless range
(approx.)
450 m
150 m
40 m
20 m