Notes For Users; Manual Release (Emergency Manouvre); Notes For Maintenance Technicians; Troubleshooting - Aprimatic ONDA 500 Notice D'installation Mécanique, D'utilisation Et D'entretien

7.

NOTES FOR USERS

IMPORTANT
At regular intervals, we recommend carrying out regular
checks by specialised personnel to ensure that the
operator is running smoothly. Do this at least once every
12 months.
7.1

Manual release (emergency manouvre)

In the event of a blackout, release the operator and open
the gate by hand:
• turn the key clockwise (
• open the release by turning completely the lever (
Re-lock the operator, at the end of the manual operation.
Slide the gate slightly in one direction, until you hear a
coupling click.
Allways the power supply must be disconnected, when
the operator is released.
Before to restore the mains power supply, it is
necessary to close the gate (closing limit switch
engaged). If not, the operator can have unexpected
functioning in response to each type of command
(Step-by-Step START, remote control, etc.).
8.

NOTES FOR MAINTENANCE TECHNICIANS

IMPORTANT - Maintenance can only be carried out by
specialised personnel.
Before servicing the operator use the differential switch to
disconnect the power supply.
For correct maintenance regularly carry out the following checks
as given in the maintenance manual issued by the installer.
Tab.3 operation
Inspect the general condition of the gate
structure and the upper guides.
Inspect the condition of wheels, guide,
couplings and limit stops.
Inspect the condition of the safety devices
(photocells, ribs...) and the performance of
the electronic clutch.
Check that the electric system and differential
switch work correctly.
Check that the input of the Stop push-button
is connected to a NC contact and that it is
working correctly.
8.1

Troubleshooting

See Tab.4.
SPACE RESERVED FOR INSTALLER
PLEASE GIVE A COPY OF THIS PAGE TO THE USER
Aprimatic S.p.A.
via Leonardo da Vinci, 414
40059 Villa Fontana di Medicina - Bologna - Italia
Tel. +39 051 6960711 - fax +39 051 6960722
info@aprimatic.com - www.aprimatic.com
ONDA 500/501/800/801
Fig.26) to release.
interval
MAX 12
months
MAX 12
months
MAX 12
months
MAX 12
months
MAX 12
months
ref.C)
TYPE OF FAULT
T H E G A T E D O E S
N O T O P E N W H E N
C O M M A N D N E D A N D
THE MOTOR DOES NOT
- .
START UP
ON GIVING THE OPENING
COMMAND THE MOTOR
-
STARTS UP BUT THE
W I N G D O E S N O T
.
MOVE
THE GATE OPENS IN
,
JERKS IS NOISY OR
.
STOPS HALFWAY
ON GIVING A CLOSING
,
COMMAND THE GATE
.
DOES NOT CLOSE
T H E K E Y R E L E A S E
O F F E R S S T R O N G
R E S I S TA N C E O R I S
.
BLOCKED ON GIVING
THE OPENING COMMAND
-
THE MOTOR STARTS UP
BUT THE GATE DOES
.
NOT MOVE
T H E G E A R M O T O R
WORKS VERY SLOWLY
BY MAKING SOUNDS
(
AND VIBRATIONS AS IF
).
IT WERE BRAKED
- 23 -
SLIDING GATES
PROBABLE CAUSES SOLUTIONS
• . •
NO POWER RESTORE THE VOLTAGE
• •
T H E C I R C U I T I S N O T CHECK THAT THE CONTROL
.
CORRECTLY CONNECTED U N I T
CONNECTED
NOT LOST CONNECTIONS
UNUSED NC CONTACT HAVE
TO BE JUMPERED
• •
THE REMOTE CONTROL IS CHECK THAT THE REMOTE
.
NOT WORKING C O N T R O L
CHARGED
•
CHECK THAT THE TRANSMITTER
AND RECEIVER CODES MATCH
•
CHECK THAT THE RECEIVER
IS WORKING
• •
THE CONTROL UNIT IS NOT CHECK THE FUSES
. •
WORKING CHECK THE OPERATING LOGIC
SETTED
• •
THE LIMIT SWITCH IS NOT C H E C K T H AT T H E L I M I T
CORRECTLY CONNECTED OR SWITCH IS CONNECTED AND
.
IS FAULTY WORKING
• . •
THE RELEASE IS OPEN C L O S E
RELEASE
• •
THE CONNECTION BETWEEN RESTORE THE CORRECT LIMIT
MOTOR AND LIMIT SWITCH SWITCH CONNECTIONS
;
IS INVERTED THE MOTOR IS
PUSHING THE WING IN THE
.
OPPOSITE DIRECTION
• . •
THE CLUTCH IS LOOSE SET THE TORQUE
• •
THE RACK IS RESTING ON THE CHECK THE RACK AGAIN AND
PINION OR THE BAR PIECES RESET IT TO THE CORRECT
.
ARE NOT EVENLY SPACED POSITION
• •
THE GUIDE HAS STEPS OR THE C H E C K T H E G U I D E A N D
.
GATE RESISTS MOVEMENT W H E E L S A N D I M P R O V E
SLIDING
• •
THE SENSITIVITY OF THE ADJUST THE TORQUE
.
CLUNCH IS NOT CORRECT SAFETY STANDARD ARE NOT
ASSURED
DEVICES
• •
T H E P O W E R O F T H E USE A MORE POWERFUL
GEARMOTOR IS INSUFFICIENT G E A R M O T O R
.
FOR THE GATE FEATURES TECHNICAL DATA
• •
T H E P H O T O C E L L S A R E CHECK PHOTOCELLS AND
.
FAULTY RELEVANT CONNECTIONS
(
SEE THE CONTROL UNIT
• •
THE CONNECTIONS ARE NOT R E S TO R E T H E C O R R E C T
.
CORRECT CONNECTION
• •
THE WING STOPS AGAINST C O R R E C T
T H E M E C H A N I C A L L I M I T POSITION AND THE BRAKING
.
BEFORE THE WING HAS BEEN TIME
,
AUTOMATICALLY STOPPED
•
CHECK THAT THE LIMIT SWITCH
CAUSING ON LOAD BLOCKING
WORKS CORRECTLY
.
OF THE GEARS
• •
THE GATE KNOCKS AGAINST REPLACE THE ELECTRICAL
,
THE MECHANICAL STOPS C O N T R O L
BEFORE OR AFTER THE BRAKE REPOSITION CORRECTLY THE
CAUSING THE BREAKDOWN END STROKE PLATES
.
OF THE ELECTRICAL BRAKE
Fig.26
Tab.4
.
I S C O R R E C T L Y
,
THAT IT HAS
.
THE
.
B A T T E R Y I S
.
.
.
.
.
.
T H E M A N U A L
.
.
.
.
.
;
IF THE
,
ADD MORE SAFETY
.
( .
S E E PA R
).
).
.
T H E P L AT E S
.
U N I T A N D
.