Product Technical Features; Destined Use And Working Range; Residual Risks; Technical Data - Aprimatic ONDA 500 Notice D'installation Mécanique, D'utilisation Et D'entretien

1.

PRODUCT TECHNICAL FEATURES

Gearmotor for residential/condominium use on sliding gates.
• Irreversible worm reduction gear (ratio 1/30) with
permanent grease lubrication.
• Pinion Z16 (standard). Z20 (available on catalogue).
• Diametral pitch 4 rack: either the plastic or the galvanized
steel one can be used; the end travel plates are the same
for both.
• M anual release with triangular key.
• Secured to the ground with foundation plate OR screw
anchors.
• Electromechanical limit switch
• Mechanical clutch: adjustable torque limiter on fast shaft.
nota: ONDA 501 and 801 are without mechanical clutch.
• The control unit can be fi tted inside the gearmotor.
note: Actuators on the catalog in version "E" (e.g.: ONDA
501 E) are sold with control unit on board.
1.1

Destined use and Working range

ONDA 500/501 operator is designed to automate the
movement of max. 500 Kg sliding gates for residential-use,
or of max. 300 kg for condominium-use.
ONDA 800/801 operator is designed to automate the
movement of max. 800 Kg sliding gates for residential-use,
or of max. 500 kg for condominium-use.
Any other use whatsoever is not authorised by Aprimatic.
Caution
It is forbidden to use the product improperly or for different
aims than those intended. It is forbidden to tamper with or
modify the product in any way whatsoever. The product
must only be installed with APRIMATIC accessories.
1.2

Residual risks

!
Warning
Take care when the gate is opening as there is a risk of injury
of hands or other parts of the body in the operating area of
the operator gear.
The operator cannot be considered a supporting part or a
safety device of the gate; the gate must be provided with
adequate support systems and safety device.
1.3

Technical data

To see Tab.1.
!
Warning
The maximum weight of the gate is only a partial
parameter for determining the limits to use, as gate
sliding MUST also be taken into account.
1.4

Overall dimensions

To see Fig.1.
1.5

Supply inspection

Ensure that the package contains all the components listed
and check for damage. Make sure the model acronym
printed on the packaging corresponds to the one affi xed on
the gear motor (Fig.2).
See the list of the
COMPONENTS SUPPLIED WITH THE OPERATOR
those to be
PURCHASED SEPARATELY
ONDA 500/501/800/801
(IP55).
and
in Tab.2 and Fig.3.
Tab.1
TECHNICAL DATA
Single-phase power supply
MAX absorbed power
Capacitor
MAX accessories current supply
MAX weight of gate (Kg)
MAX number of daily cycles
Rated thrust force (N)
(1N≅0,102Kg)
Rated wing speed
MAX. shaft torque
Gearmotor weight
Degree of protection
Operating temperature
when the control unit is inside
in case of external control unit
48
245
- 15 -
SLIDING GATES
ONDA ONDA
500/501 800/801
230V 50÷60Hz ± 10%
230W 260W
20μF 25μF
1 A
Z16 : 500/300* 800/500*
Z20 : 300/200* 500/300*
100 50
Z16 : 940 N 1250 N
Z20 : 750 N 1000 N
Z16 : 9,5 m/min
Z20 : 12 m/min
3
10 Kg
IP 44
-25 ÷ +70 °C
-25 ÷ +90 °C
* residential/condominium
Fig.1
39 130 23
191
199
Fig.2
4