Installation Checklist; Date Of Manufacture - 3M DBI SALA LAD-SAF Instructions D'installation

5.0 INSPECTION
5.1 INSPECTION FREQUENCY:
For information on inspection frequency, inspection steps and use of the Lad-Saf Flexible Cable Safety System, refer to
instructions for use (IFU) 3M Fall Protection manuals 5908555, 5908556 and 5908301.
5.2 RFID TAG:
The Lad-Saf system includes a Radio Frequency Identification (RFID) tag (Figure 17). The RFID tag can be used in
™
conjunction with a handheld reading device and web based portal to simplify inspection and inventory control and provide
records for your fall protection equipment. If you are a first-time user, contact a 3M Fall Protection Customer Service
representative (see back cover). If you have already registered, go to 3M.com/FallProtection. Follow the instructions
provided with your handheld reader or on the web portal to transfer your data to your web log.
6.0 MAINTENANCE, SERVICING, STORAGE
6.1
If the carrier cable becomes heavily soiled with oil, grease, paint, or other substances, clean it with warm soapy water.
Wipe off the cable with a clean, dry cloth. Do not force dry with heat. Do not use acid or caustic chemicals that could
damage the cable.
7.0 SPECIFICATIONS
7.1 All top and bottom brackets, cable guides, carrier cable, and fasteners are made of galvanized or stainless steel. Contact
3M Fall Protection for material specification details if required. The LAD-SAF™ system, when installed according to the
installation instructions, meets OSHA 1910.140, OSHA 1926.1053, OSHA 1910.29, OSHA 1926.502, ANSI Z359.16, CSA
(Z259.2.5) and CE (EN353-1:2014+A1:2017) requirements.
Declaration of Compliance: www.3M.com/FallProtection/DOC
8.0 LAD-SAF SYSTEM LABELING
; Please reference the User Manual supplied with the Lad-Saf™ Detachable Sleeve for proper use and maintenance of this system.
The Lad-Saf Flexible Cable Safety System Tag must be securely attached and fully legible. (See Figure 17) System Tag
contents are listed in Table 1.
The System Tag includes the following warning:
WARNING: Failure to heed warnings may result in serious injury or death. Manufacturer's instructions supplied
with this product at time of shipment must be followed for proper installation, use, inspection and maintenance.
Unauthorized alteration or substitution of system elements or components is prohibited. Use only with compatible
personnel protective equipment as per manufacturer's instructions. Before each use inspect system visually for defects.
Formally inspect system in accordance with instructions at least annually, or in accordance with specified inspection
criteria for the structure the system is secured to. Refer to instructions for information on periodic formal inspections.
Minimum spacing of users of this system is 20ft (6m). Do not remove this label.
A Single Point Anchor Warning is stamped on the washer at the top of Systems L1, L2, L3 and CE1. See Table 1 and
Figure 18. For the M1 and M2 systems, the same information is stamped onto the D-ring bracket. See Figure 4.

INSTALLATION CHECKLIST

Serial Number(s):
Date Inspected:
Install Date:
Installed By:
Corrective Action/Maintenance

Date Of Manufacture:

Ensure all fasteners are in place and properly tightened.
Ensure the Carrier Cable is properly tensioned
Ensure the Carrier Cable does not abrade against the structure at any
point.
Ensure system information is recorded on the system label and
Inspection and Maintenance Log:
Components of the LAD-SAF system include a Radio Frequency (RFID) tag.
The RFID tag can be used in conjunction with the handheld reading device and
web based portal (3M.com/FallProtection) to simplify inspection and inventory
control, and maintain electronic records for your fall protection equipment.
16