Table des Matières
Publicité
1.0
PRODUCT APPLICATION
1.1
PURPOSE: The 3M DBI-SALA LAD-SAF™ Flexible Cable Safety System (Figure 1) is part of a personal fall protection
system. When used in combination with the Lad-Saf™ Detachable Cable Sleeve (sold separately), the Lad-Saf™
Flexible Cable Safety System is designed to protect a worker in the event of a fall while climbing fixed ladders or similar
climbing structures. LAD-SAF
climbing surfaces that are part of a structure (e.g., mono poles [wood, steel, or concrete] buildings, manways, antenna
structures and towers). The personal protection equipment (PPE) which is selected will form an essential part of the
system. Always wear a full body harness with a sternal (chest) attachment point, in accordance with ANSI Z359.11 or
with the relevant national standard. When climbing, the user of the system should wear a climbing helmet which conforms
to the national standard.
1.2
LIMITATIONS: LAD-SAF™ Flexible Cable Safety Systems are not intended to be installed on portable ladders. LAD-SAF™
Flexible Cable Safety Systems are designed for use on structures that are generally vertical. The safety system must not
exceed a maximum angle of 15° from vertical. The following application limitations must be considered before installing
the LAD-SAF™ Flexible Cable Safety System.
A.
STRUCTURE: The structure to which the LAD-SAF™ Flexible Cable Safety System is installed must be capable of
withstanding the loads applied by the system in the event of a fall (see Section 2.2).
B.
SYSTEM CAPACITY: The number of users allowed on the LAD-SAF™ Flexible Cable Safety System at one time
varies depending on the type of system and installation. Generally, LAD-SAF™ Flexible Cable Safety System
capacities range from one to four users. See Table 2 for more information on capacity limitations. LAD-SAF™
Flexible Cable Safety System capacities are based on a maximum user weight of 310 lbs (140kg), including tools and
clothing.
C.
ENVIRONMENTAL HAZARDS: Use of the LAD-SAF™ Flexible Cable Safety System in areas with environmental
hazards may require that additional precautions be taken to reduce the possibility of injury to the user or damage to
the equipment. (e.g., high heat caused by welding or metal cutting, caustic chemicals, seawater, high voltage power
lines, explosive or toxic gases, moving machinery, sharp edges).
1.3
SUPERVISION: Installation of the LAD-SAF™ Flexible Cable Safety System must be supervised by a Qualified Person
1.4
TRAINING: The LAD-SAF™ Flexible Cable Safety System must be installed by persons trained in its correct application.
This manual is to be used as part of an employee training program as required by OSHA. It is the responsibility of
the installers of this equipment to ensure they are familiar with these instructions, trained in the correct care of this
equipment.
1.5
Refer to applicable local, and national requirements governing this equipment for more information on vertical safety
systems and associated components, including OSHA 1910.140, OSHA 1910.29, OSHA 1926.1053 and OSHA 1926.502.
2.0
SYSTEM CONSIDERATIONS
2.1
COMPATIBILITY OF COMPONENTS AND SUBSYSTEMS: This equipment is designed for use with 3M Fall Protection
approved components and subsystems. The use of non-approved components and subsystems (e.g., harnesses, lanyards,
sleeves, etc.) may jeopardize compatibility of equipment, and could affect the safety and reliability of the complete
system. If you have questions on the installation or suitability of this equipment for your application, contact 3M Fall
Protection.
COMPATIBILITY WITH CLIMB ASSIST SYSTEMS: 3M Fall Protection LAD-SAF™ Flexible Cable Safety Systems,
including 3M Fall Protection LAD-SAF™ Detachable Cable Sleeves, are designed for use with 3M Fall Protection approved
climb assist systems. The use of any other type of climb assist system may be incompatible with the LAD-SAF™
Flexible Cable Safety System and LAD-SAF™ Detachable Cable Sleeves, and could create a serious safety hazard for
the user. Do not use non-3M Fall Protection climb assist systems without first consulting a competent person and/or a
qualified person at your worksite for approval. If you have additional questions about compatibility, please contact 3M
Technical Services.
; ANSI Z359.1-2007 Safety Requirements for Personal Fall Arrest Systems, Subsystems and Components, requires a competent person
and/or a qualified person to "ensure that systems assembled from components and subsystems made by different manufacturers meet
the requirements of this standard."
1 Qualified Person:
A person with a recognized degree of professional certificate and with extensive knowledge, training, and experience in the fall protection
and rescue field who is capable of designing, analyzing, evaluating, and specifying fall protections and rescue systems to the extent required by OSHA and other ap-
plicable standards.
Flexible Cable Safety Systems are intended to be installed on fixed ladders or ladder like
™
12
.
1
Publicité
Table des Matières
