Rf Commands Programming; Times Programming - Aprimatic ADI R230E Instructions

9. RF COMMANDS PROGRAMMING

To change the keys-RF commands confi guration, proceed as follows:
1. Press SW1 (RF commands programming key). The appliance beeps twice slowly signalling the beginning
of the learning phase.
2. Using an already programmed remote control, press in sequence the keys corresponding to the Channel 1,
Channel 2, Centralized Activation and Centralized Deactivation commands; after every learning a number of
beeps equal to the number of already programmed commands will be emitted.
All assignments are facultative. To skip a position, press SW2 (times programming key - see fi g.2.3) instead
of the key of the remote control.
3. At the end of the learning phase, the procedure ends automatically (two slow beeps will be emitted).
Information
If you make a mistake (for instance more commands assigned to the same key), a number of short beeps will
be emitted at the end of the programming phase. In this case, it is possible to re-program the keys starting from
the one to which the "Channel 1" command has been assigned.
If, after entering the learning phase, no key is pressed within 15 seconds, the procedure ends automatically
(time-out); any previous learning will remain valid.
If you make a mistake and you want to quit the procedure, wait until the procedure ends automatically
without pressing any key (see above) or press SW1 (RF commands programming key): even in this case
any previous learning will remain valid.
If you want to change the parameters after the installation of the module and the latter is not easily accessible,
the procedure can be done via radio.
a - Press keys 1-4-5-8 simultaneously (TR14) or all keys (TR2 or TR4) until hearing a short beep, then
release the keys.
b - Within 5 seconds, repeat the operation while holding the keys pressed until hearing two short beeps followed
by two long beeps signalling the beginning of the learning phase.
Now proceed as described above and remember that you have to press again keys 1-4-5-8 (TR14) or all
keys (TR2 or TR4) to skip a key position.
ENGLISH

10. TIMES PROGRAMMING

In standard confi guration the timer times for channels 1 and 2 are equal to 45 seconds or 45 minutes depending on
the operation logic selected (see par.8). If you want to change these parameters, proceed as follows:
1. Press SW2 (times programming key 3) until hearing three long beeps: the programming phase is in progress.
2. Press the button or key of the remote control corresponding to the "Channel 1" command: the countdown starts
automatically and one beep is emitted after every second elapsed.
3. Count the beeps. When you reach the number required for the timer time for channel 1 (equivalent to
the number of seconds or minutes of the required activation time), press again the button or key of the
remote control. The countdown stops and the new setting is stored in the memory of the appliance which
beeps twice shortly to confi rm.
4. Repeat steps 2 and 3 for programming the timer time for channel 2.
5. When both parameters have been programmed, the procedure stops automatically (three long beeps
will be emitted).
Information
The pause time must always be programmed even if the selected logic is not the Automatic one: in this case,
the new setting will not affect the functioning.
If, after entering the programming phase, no key is pressed within 15 seconds, the procedure stops automatically
(time-out); any previous programming will remain valid.
If you make a mistake and you want to quit the procedure, wait until the procedure ends automatically
without pressing any key (see above) or press SW1 (RF commands programming key): even in this case
any previous learning will remain valid.
If you want to change the parameters after the installation of the module and the latter is not easily accessible,
you can proceed as mentioned above via radio.
A - Press keys 1-4-5-8 simultaneously (TR14) or all keys (TR2 or TR4) until the module beeps shortly,
then release the keys.
B - Within 5 seconds, repeat the operation until the module beeps twice shortly, then release the keys.
C - Again, within 5 seconds, repeat the operation and hold the keys pressed until hearing three short beeps
followed by three long beeps signalling that the programming phase is in progress.
Now proceed as mentioned.
5 5