FYTTER RU003B Mode D'emploi page 4

ENGLISH
In order to decrease the risk of suffering severe injuries, read carefully all the important instructions and warnings
regarding the use of a treadmill before using it.
FYTTER doesn't take any responsibility for personal injuries or proterty damages resulting from the use of this
product.
1-Before starting any workout programm, consult your doctor. It's specialky important for people older than 35
years old, people with health problem and pregnant women.
2-The owner must ensure that all users are correctly informed about the warnings.
3-Use the equipment as explained in the instructions manual.
4-Keep the equipment in an enclosed area, away from dust or humidity. Don't store it in a garage, indoor
backyard or near the water. Humidity, dust and water could lead to a malfunction of the equipment,
anulling its guarantee.
5-Place the unit on a flat surface. If the surface is uneven, the proper functioning could be affected. Some models
include levellers or levelling threads behind the legs, helping the levelling. Please read the manual to verify if your
unit is provided with one of them..
6-The unit must be placed in a ventilated area. Don't use it in places with sprays or with oxygen dispenser. The air
you breath may be affected and cause an accident.
7-Keep children younger than 12 years old and pets away from the equipment. Keep the security distance.
8-Check in the manual the maximum weight your equipment can support. An excessive weight could lead
to a malfunction in the operating system, which won't be covered by the guarantee.
9-Wear suitable clothes and shoes. Do not use loose clothe that may get hooked.
10-If your equipment is working through a power supply: make sure that the power cord and plug are in good
conditions. Carry out the connection only when the circuit has ground connection, otherwise it could cause
damages on the equipment or in the property which the guarantee won't cover. Power cords must be away from
hot surfaces.
11-If it is a battery-powered unit: check and make sure that they are charged enough so the display will fully
function.
12-If your equipment is provided with a security key, please understand the produce before using it. The security
key has a magnet which must be put in the display. At the end of the lace there is a clamp which should be attached
to the clothes.The treadmill will start working only if the key is placed in the display.THIS IS ESSENTIAL.
13-If your unit works thanks to a power supply: don't put it into operation while you are on the belt. The motor
would be innecesarily loaded. The right way is placing yourself with open legs, each one on a side of the belt and
sit up once it is ongoing.
14-If your unit works with an electric supply: check the speed it can reach, for your security. The best is to adjust
gradually the speed in order to avoid sudden changes.
15-If your unit works through an electric supply: never leave the machine unattented while it's working.
Take the security key off, turn the "on" button into "off" and unplug the power cord.
16-If your equipment is provided with a pulse sensor, you may know it isn't a medical instrument. It's designed as
a help for the workout and determines the tendencies of heart rates. There are some factors which could affect the
accuracy of the heart rate interpretations, for example the movements of the user.
17-FYTTER machines don't take too much space as they can be folded. Once folded, make sure that all is well
assembled to the locking system, either if it has a lock or an hidraulic engine. Don't try to move it or raise unless
you are insured. Should any damage happen being the machine uninsured, it won't be covered by the guarantee.
18-Check and tighten all screws on a regular basis, because due to vibrations screws and nuts tend to
loosen. Damages caused by a lack of maintenance won't be covered by the guarantee.
19-A correct lubrication of the treadmill with silicon oil or teflon is REALLY IMPORTANT. This lubrication
must be performed regularly depending on each person, even before its first use.The lubrication must be carried
out this way: disconnect the equipment of the electricity supply (in case you have one), pull up the tapestry from
the side with one hand and spread the oil on the board. Please repeat this procedure from the other lateral side.
Connect the equipment to the power supply (in case you have one) und turn the "on" button (red button) into the
FYTTER |WWW.FYTTER.COM PAG- 3