Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Support your arm so it is relaxed.
Ensure that the cuff is at the same height as your heart.
6. Press the ON/OFF button 1 to start the measurement.
On/Off button
7. The cuff will now pump up automatically. Relax, do not move
and do not tense your arm muscles until the measurement
result is displayed. Breathe normally and do not talk.
8. When the correct pressure is reached, the pumping stops
and the pressure falls gradually. If the required pressure was
not reached, the instrument will automatically pump some
more air to the cuff.
9. During the measurement, the heart symbol AN flashes in the
During the measurement, the heart icon
10. The result, comprising the systolic AQ and the diastolic AR
blood pressure and the pulse AS is displayed and longer beep
is heard. Note also the explanations on further displays in
this booklet.
11. When the measurement has finished, remove the cuff and
pack it into the instrument as shown in Fig. II.
12. Enter the result in the enclosed blood pressure pass and
switch off the instrument. (The monitor does switch off auto-
matically after approx. 1 min.).
You can stop the measurement at any time by pressing the
ON/OFF button (e.g. if you feel uneasy or an unpleasant
pressure sensation).
4. Appearance of the Heart Arrhythmia Indicator for
early Detection
This symbol AM indicates that certain pulse irregularities were
detected during the measurement. In this case, the result may
deviate from your normal blood pressure – repeat the measure-
ment. In most cases, this is no cause for concern. However, if the
symbol appears on a regular basis (e.g. several times a week with
measurements taken daily) we advise you to tell your doctor.
Please show your doctor the following explanation:
Information for the doctor on frequent appearance of the
Arrhythmia indicator
This instrument is an oscillometric blood pressure monitor that
also analyses pulse frequency during measurement. The instru-
ment is clinically tested.
14
1 to start the measurement.
AN
is fl ashing.
The arrhythmia symbol is displayed after the measurement, if
pulse irregularities occur during measurement. If the symbol
appears more frequently (e.g. several times per week on
measurements performed daily) we recommend the patient to
seek medical advice.
The instrument does not replace a cardiac examination, but
serves to detect pulse irregularities at an early stage.
6. Data Memory
5.
At the end of a measurement, this instrument automatically stores
each result, including date and time.
Viewing the stored values
Press the M-button AT briefly, when the instrument is switched
off. The display first shows «M» AP and then a value, e.g. «M 17».
This means that there are 17 values in the memory. The instrument
then switches to the last stored result.
Pressing the M-button again displays the previous value. Pressing
the M-button repeatedly enables you to toggle between one
stored value and another.
Memory full
When the memory has stored 200 results, the display shows
When the memory has stored 60 results, the memory is full.
«Full M» after a measurement. From this point onwards, a
From this point onwards, a new measured value is stored
new measured value is stored by overwriting the oldest
by overwriting the oldest value.
value
Delete a measurement
Select the measurement value you want to delete. Press the
ON/OFF Button and keep it pressed for approx. 10 seconds until
the memory symbol fl ashes. Confi rm your deletion request by
pressing the memory button. "CL" appears briefl y on the display
and the value you selected has been deleted. The display returns
to standby mode.
Clear all values
If you are sure that you want to permanently remove all stored
values, hold down the M-button (the instrument must have been
switched off beforehand) until «CL» appears and then release the
button. To permanently clear the memory, press the M-button
while «CL» is flashing. Individual values cannot be cleared.
aponorm
®
by
Publicité
Chapitres
Table des Matières
