SRAM RockShox PIKE Manuel De L'utilisateur page 4

English
reMote installation
The PopLoc or PushLoc Remote Lockout lever allows the rider to control the movement of their suspension
fork without removing their hands from the handlebars. Specific left and right levers are available.
If needed, remove the grip, brake lever, and shifter from the handlebar. If you are unfamiliar with the
removal of these items, please consult the manufacturer's instructions.
. Slide the Poploc onto the handlebar, or install the PushLoc on the handlebars.
2. Re-install the shifter, brake lever, and grip on the handlebars. If you are unfamiliar with the installation
of these items, please consult the manufacturer's instructions. Always adhere to the recommended
torque specifications for these items.
3. Position the PopLoc or PushLoc as desired on the handlebar and tighten the clamp bolt
to 20in-lb (2.25 Nm).
4. Forks with PopLoc Adjust: Turn the blue compression adjustment dial counterclockwise until it stops.
5. Verify that the PushLoc or PopLoc is in the "open" position. To do this, press the lever on the PushLoc
until it returns towards the rider. Press the release button on the PopLoc.
6. Install the cable in the PopLoc or PushLoc.
7. Install the cable into the housing.
8. Feed the cable and housing into the cable stop on the fork crown.
9. Gently pull on the cable and align it with the groove in the rotating cam of the Motion Control damper.
0. Tighten the cable fixing bolt on the rotating cam to 8in-lb (.9 Nm).
i m p o r t a n t
consumer safety information
The Maxle Quick Release system allows the use of a standard 20mm X 0mm
thru-axle hub for enhanced stiffness. The axle threads into the left fork leg,
tightening the hub against the left drop out. The axle is fixed in place in the
lower leg by the Maxle Quick Release lever.
Riding with an improperly installed wheel can allow the wheel to move or
disengage from the bicycle, causing damage to the bicycle, and serious injury or
death to the rider. It is essential that that you:
• Ensure that your axle, dropouts, and quick release mechanisms are clean and
free of dirt or debris.
• Ask your dealer to help you understand how to properly secure your front
wheel using the Maxle Quick Release System.
• Apply the correct techniques when installing your front wheel.
• Never ride your bicycle unless you are sure the front wheel is installed
properly and secure.
4
Pike, Reba, Revelation, Domain & Argyle User Manual
95-405-000-000, Rev. A
Pike, Reba, Revelation, Domain & Argyle User Manual
Maxle 360° QUiCK release systeM
installation
. Position your wheel in the dropouts of the lower leg. The hub should seat firmly in the dropouts. Be
sure to position the rotor in the caliper. Verify that neither the rotor, hub, nor rotor bolts interfere with
the lower legs. If unfamiliar with adjusting your disc brake, see your brake manufacturer's instruction.
tighten
. Place Maxle lever in the open position (fig. a). Ensure the lever
engages with the corresponding slot in the axle.
2. Slide the axle through the right side of the hub until it engages
the threads of the left drop out.
3. To tighten the axle into the dropout, turn the axle lever clockwise
until hand tight.
w a r n i n g
DIRT AND DEBRIS CAN ACCUMULATE BETWEEN THE DROPOUT
OPENINGS. ALWAYS CHECK AND CLEAN THIS AREA WHEN REINSTALLING
THE WHEEL. ACCUMULATED DIRT AND DEBRIS CAN COMPROMISE THE
SECURITY OF THE AXLE, LEADING TO SERIOUS AND/OR FATAL INJURY.
notes: Never use any other tool to tighten the axle into the lower leg. Over-tightening of the axle can
damage the axle and/or the lower leg.
secure
. To lock the axle into the lower leg close the Maxle quick release lever.
2. The quick release mechanism is an "over-center cam", similar to the quick release found on many
bicycle wheels. When closing the lever, tension should be felt when the quick release lever is in the
horizontal position (90 degrees to the lower leg), and the quick release lever should leave an imprint
in the palm of your hand. If resistance is not felt at the 90 degree position and if the lever does not
leave a clear imprint in the palm of your hand, tension is insufficient. To increase tension, open the
quick release lever turn the quick release lock nut in small increments until proper tension is felt.
A small (1-2mm) gap may be noticed between the inside flange of the maxle and the outside of the dropout.
This gap is normal, and allows the right leg to "Float" in position prior to closing of the quick release.
w a r n i n g
AFTER CLOSING THE MAXLE QUICK RELEASE LEVER, DO NOT
REPOSITION OR SPIN THE LEVER. REPOSITIONING OR SPINNING
THE MAXLE LEVER CAN CAUSE THE AXLE TO COME LOOSE,
COMPROMISING THE SECURITY OF THE AXLE.
© SRAM Corporation • May 2006
English
fig. a
5