Technical Description; Technical Features; Safety - Calpeda SD Instructions Pour L'utilisation

1.2. Manufacturer name and address
Manufacturer name: Calpeda S.p.A.
Address: Via Roggia di Mezzo, 39
36050 Montorso Vicentino - Vicenza / Italia
www.calpeda.it
1.3. Authorized operators
The product is intended for use by expert operators
divided into end users and specialized technicians.
(see the symbols above).
It's forbidden, for the end user, carry out
i
operations which must be done only by
specialized technicians. The manufacturer
declines any liability for damage related to
the non-compliance of this warning.
1.4. Warranty
For the product warranty refer to the general terms
and conditions of sale.
The warranty covers only the replacement
i
and the repair of the defective parts of the
goods (recognized by the manufacturer).
The Warranty will not be considered in the following
cases:
- Whenever the use of the device does not conform
to the instructions and information described in this
manual.
- In case of changes or variations made without
authorization of the manufacturer.
- In case of technical interventions executed by a
non-authorized personnel.
- In case of failing to carry out adequate maintenance.
1.5. Technical assistance
Any further information about the documentation,
technical assistance and spare parts, shall be
requested from: Calpeda S.p.A. (paragraph 1.2).

2. TECHNICAL DESCRIPTION

Submersible borehole pumps for 4" wells (DN 100
mm), 6" wells (DN 150 mm), 8" (DN 200 mm) and 10"
(DN 250 mm).
Delivery casing with built-in non-return valve.
2.1. Intended use
- For clean or slightly dirty water with maximum sand
content: 150 g/m (50 g/m
3
HIGH SAND versions).
- Water temperature up to 25 °C (35 °C for 4").
2.2. Improper use
The device is designed and built only for the purpose
described in paragraph 2.1.
Improper use of the device is forbidden, as
is use under conditions other than those
indicated in these instructions.
Improper use of the product reduces the safety and
the efficiency of the device, Calpeda shall not be
responsible for failure or accident due to improper
use.
2.3. Marking
The following picture is a copy of the name-plate (see
Pic.1) that is on the external case of the pump.
SD, SDX, SDS_Rev15 - Operating Instructions
for SDX), (300 g/m for
3 3
1 Pump type
2 Delivery
3 Head
1
4 Rated power
2
5 Notes
3
6 Weight
4
7 Rotation speed rpm
8 Serial number
9 Certifications
5

3. TECHNICAL FEATURES

3.1. Technical data
Dimensions and weight (see technical catalogue).
Nominal speed 2900/3450 rpm
Supply voltage / Frequency (see data on the engine
indicator plate).
Maximum permissible working pressure:
SD,SDN,SDF 400 m (40 bar)
SDS 500 m (50 bar)
SDX 700 m (70 bar)
Max. starts per hour: (see instruction motor).

4. SAFETY

4.1. General provisions
Before using the product it is necessary to
know all the safety indications.
Carefully read all operating instructions and the
indications defined for the different steps: from
transportation to disposal.
The specialized technicians must carefully comply
with all applicable standards and laws, including local
regulations of the country where the pump is sold.
The device has been built in conformity with the
current safety laws. The improper use could damage
people, animals and objects.
The manufacturer declines any liability in the event of
damage due to improper use or use under conditions
other than those indicated on the name-plate and in
these instructions.
Follow the routine maintenance schedules
i
and the promptly replace damaged parts,
this will allows the device to work in the best
conditions.
Use only original spare parts provided from Calpeda
S.p.A or from an authorized distributor.
Don't remove or change the labels placed on
the device.
Do not start the device in case of defects or damaged
parts.
Maintenance operations, requiring full or
partial disassembly of the device, must be
done only after disconnection from the supply.
4.2. Safety devices
The device has an external case that prevents any
contact with internal parts.
4.3. Residual risks
The appliance, designed for use, when used in-
line with the design and safety rules, doesn't have
MONTORSO VICENZA
Made in Italy
XXXXXXX XXXXXXX
Q min/max X/X m /h
3
H max/min X/X m
X kW (XHp) n XXXX/min
S.F.
X kg
XXXXXXXX
Page 9 / 72
9
8
7
GB
6