Ce Conformity Declaration - Multiplex RX-5-SYNTH IPD CAR Instructions

! These operating instructions are an integral part
of this product. They contain important information
and safety notes, and should therefore be kept in a
safe place at all times. Be sure to pass them on to
the new owner if you ever dispose of the product.
1. S
PECIFICATION
RX-5 SYNTH IPD CAR
Order No.
Servo channel count
Reception system
Sensitivity
Current drain
Operating voltage
Servo channel count
from transmitter
Available RF-channels /
spot frequencies
Permissible operating
temperature range
Aerial length
Dimensions L x W x H
Weight
1)
41 MHz for export only; prohibited in Germany.
2)
A low-voltage power-on guard prevents the receiver operating
if switched on with a voltage below 4.5 V. Once operating, the
receiver works without problem down to a voltage of 3.5 V.
2. S N
AFETY OTES
! Read the instructions before using the receiver for the
first time
! Use the receiver for its intended application only (
! Be sure to use a power supply of adequate capacity
( 8.)
! Read and observe the installation notes (
! Carry out regular range checks (
! Keep strictly to the following sequence when switching
on and off:
First switch the transmitter ON, then switch the receiver ON.
First switch the receiver OFF, then switch the transmitter
OFF.
! Note: regarding mixed operation
MULTIPLEX RX-SYNTH receivers can also be operated in
conjunction with transmitters not exploiting Synthesizer
technology, i.e. those using conventional plug-in crystals.
Synthesizer technology simply provides a modern, con-
venient, extremely flexible and highly accurate method of
generating a frequency.
All MULTIPLEX RX-SYNTH IPD receivers work on the basis
of the FM / PPM transmission process, which is compatible
with most other makes of RC equipment. This means that
mixed operation with FM/PPM transmitters of other makes is
possible in principle. However, we cannot guarantee that
such a system will work perfectly, as there are too many
possible combinations for us to check.
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten (Gölshausen) • www.multiplex-rc.de
Operating Instructions
RX-5 SYNTH IPD CAR receiver – Software V 1.2x
1)
40/41 MHz
# 5 5896
5
FM/PPM single conversion with IPD
(Intelligent Pulse Decoding)
approx. 2 V
approx. 20 mA (excl. servos)
2)
3.5 ... 7.5 V
4 – 5 NiCd/NiMH cells
compatible with FM/PPM transmitters
with at least two servo channels.
see page 6
- 15°C ... + 55°C
450 mm
approx. 44 x 29 x 17 mm
approx. 21 g
21.)
22.)
3. S
PECIAL
PLL synthesizer receivers, requiring no plug-in crystals
Quick, simple change of RF channel using automatic
channel search, with Lock-on security by confirmed
channel acceptance from the transmitter
Use of standardised FM/PPM transmission format ensures
compatibility with other makes of equipment
IPD decoder (Intelligent Pulse Decoding) with HOLD and
FAIL-SAFE functions
Error counter
4. I
NTENDED
The RX-5 SYNTH IPD CAR receiver is designed exclusively for
use as a radio control receiver for model sport applications. Its
use in man-carrying vehicles or industrial apparatus is prohi-
bited.
5. CE C
ONFORMITY
This device has been assessed in accordance with the
relevant harmonised European directives.
You are therefore the owner of a product whose design
fulfils the protective aims of the European Community relating to
the safe operation of equipment.
The detailed CE conformity declaration can be downloaded in the
form of a PDF file from the Internet under www.multiplex-rc.de. It
is located in the DOWNLOADS area under PRODUCT INFOR-
MATION.
6. Q S
UICK
1. Switch transmitter ON
2. Connect the receiver battery to the receiver and switch on
LED flashes (RF channel search):
LED Code 2
The RF channel search is concluded when the LED glows
constantly:
LED Code 1
4.)
3. Move any transmitter stick four times steadily to one end-
point
The LED must switch OFF/ON in time with the stick
movement
4. The RF channel setting procedure is concluded; the LED
flashes:
LED Code 5
5. Switch the receiver OFF, then ON again
The receiver is ready for use; the LED flashes:
LED Code 3
F
EATURES
A
PPLICATION
D
ECLARATION
TART
1,6 sec
LED ON
1,6 sec
1,6 sec
Page 1/6