Intended Application; Ce Conformity Declaration - Multiplex RX-7 SYNTH IPD Instructions D'utilisation

!
These operating instructions are an integral part of this
product. They contain important information and safety notes,
and should therefore be kept in a safe place at all times. Be sure
to pass them on to the new owner if you ever dispose of the
product .
1. S
PECIFICATION
35 MHz
RX-7 SYNTH IPD
A-band
# 5 5880 # 5 5881 # 5 5882 # 5 5883 # 5 5884
Order No.
Reception system
with IPD (Intelligent Pulse Decoding)
Dimensions
L x W x H
Weight
RX-7 SYNTH
35 MHz
DS IPD
A- and
# 5 5885 # 5 5886 # 5 5887 # 5 5888 # 5 5889
Order No.
Reception system
with IPD (Intelligent Pulse Decoding)
Dimensions
L x W x H
Weight
Specification: RX-7 SYNTH IPD and RX-7 SYNTH DS IPD
Available RF chan-
nels / spot frequen-
cies
Channel count
Servo channel
count from trans-
mitter
Sensitivity
Current drain
Aerial length
Operating voltage
Permissible operat-
ing temperature
range
1)
36, 41 and 72 MHz for export only; prohibited in Germany
2)
A low-voltage power-on guard prevents the receiver operating if
switched on with a voltage below 4.5 V. Once operating, the receiver
works without problem down to a voltage of 3.5 V.
2. S N
AFETY OTES
! Read the instructions before using the receiver for the first time
! Use the receiver for its intended application only (
! Be sure to use a power supply of adequate capacity (
! Read and observe the installation notes (
! Carry out regular range checks (
! Keep strictly to the following sequence when switching
on and off:
First switch the transmitter ON, then switch the receiver ON
First switch the receiver OFF, then switch the transmitter OFF
! Note regarding mixed operation
MULTIPLEX RX-SYNTH receivers can also be operated in conjunc-
tion with transmitters not exploiting Synthesizer technology, i.e.
those using conventional plug-in crystals. Synthesizer technology
simply provides a modern, convenient, extremely flexible and
highly accurate method of generating a frequency.
MULTIPLEX Modellsport GmbH & Co.KG • Neuer Weg 2 • D-75223 Niefern-Öschelbronn • www.multiplex-rc.de
Operating Instructions Receiver
RX-7 SYNTH / RX-7 SYNTH DS IPD — Software V 1.1x
1)
35 MHz 40/41
1)
36 MHz
B-band MHz
FM/PPM single conversion
44 x 29 x 17 mm
approx. 23 g
1)
35 MHz 40/41
1)
36 MHz
B-band MHz
FM/PPM dual conversion
56 x 22.5 x 24.5 mm
approx. 25 g
see page 6
7
min.: 2 / max.: 9
approx. 2 V
approx. 15 mA (excl. servos)
approx. 900 mm
2)
3.5 ... 7.5 V
4 — 5 NiCd / NiMH cells
- 15°C ... +55°C
4.)
8.)
22.)
23.)
All MULTIPLEX RX-SYNTH IPD receivers work on the basis of the FM /
PPM transmission process, which is compatible with most other
makes of RC equipment. This means that mixed operation with
FM/PPM transmitters of other makes is possible in principle.
However, we cannot guarantee that such a system will work
perfectly, as there are too many possible combinations for us to
check.
3. S F
PECIAL
1)
72MHz
PLL synthesizer receivers, requiring no plug-in crystals.
Quick, simple change of RF channel using automatic channel search,
with Lock-on security by confirmed channel acceptance from the
transmitter.
Use of standardised FM/PPM transmission format ensures compati-
bility with other makes of equipment
IPD decoder (Intelligent Pulse Decoding) with HOLD and FAIL-SAFE
functions
Error counter
1)
72MHz
4. I
NTENDED
The RX-7 SYNTH IPD and RX-7 SYNTH DS IPD receivers are designed
exclusively for use as radio control receivers for model sport applications.
Their use in man-carrying vehicles or industrial apparatus is prohibited.
5. CE C
ONFORMITY
MULTIPLEX Modellsport GmbH & Co.KG declares that these devices
fulfil the requirements of the following harmonised directives of the
European Union (EU):
Protection requirements concerning electro-magnetic compati-
bility
EN301 489
Measures for the efficient use of the radio frequency spectrum
EN300 220
6. Q S
UICK TART
1. Switch the transmitter on.
2. Connect the receiver battery to the receiver and switch on.
LED flashes (RF channel search):
LED Code 2
The RF channel search is concluded when the LED glows constantly:
LED Code 1
3. Move any transmitter stick four times steadily to one end-point.
the LED must switch OFF / ON in time with the stick movement.
4. The RF channel setting procedure is concluded; the LED flashes:
LED Code 5
5. Switch the receiver OFF, then ON again.
The receiver is ready for use; the LED flashes:
LED Code 3
EATURES
A
PPLICATION
D
ECLARATION
1,6 sec
LED ON
1,6 sec
1,6 sec
Page 1/6