Maintenance / Disposing; Technical Data; Special Accessories - Intimus 45 SC2 Instructions D'opération

GB
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
MATERIAL JAM IN THE MACHINE:
(Auto reverse function)
If a jam is caused by too much material being fed
in the following happens:
- The cutters jam, then run in reverse for a short
time (material is released) and stop. The motor
switches off. The control display
on.
Proceed as follows:
Paper jam in paper feed slot (11)
- Remove the paper that has been fed back.
- The cutters now run forwards automatically
and shred the remaining paper in the cutters.
During the forward run the forward button (3)
LED display comes on. The control display
(6) goes out.
- Continue shredding with less paper.
- If necessary, switch the cutters manually
alternately from forward to reverse until the
material has gone through completely and
been shredded.
CLEANING THE PHOTOCELLS (Fig. 5):
If paper particles should come to rest in the
inlet guide (for example after a paper jam) it is
possible that the machine will not turn off, due to
the broken light barrier.
To remove these paper strips and also to clean
the photocell, pass another sheet of paper
through the feed slot, or switch the machine to
reverse and wipe both "eyes" of the photocell
with a brush.
fig. 5
Model
intimus 45/60SC2 220-230V/50Hz · 3,0
intimus 45/60CC3+CC4+CC5 220-230V/50Hz · 3,0
intimus 45/60CC6 220-230V/50Hz · 3,0
Pre-fusing (slow-blow): 220-230V = 10 amps / 120V = 15 amps / 100V = 15 amps
Model Type
intimus 45SC2 278-4S
intimus 45CC3 278-4C
intimus 45CC4
278-2C
intimus 45CC5
278-1C
intimus 45CC6
278-1CF
intimus 60SC2
279-4S
intimus 60CC3
279-4C
intimus 60CC4
279-2C
intimus 60CC5
279-1C
intimus 60CC6
279-1CF
MALFUNCTIONS
LIGHT BARRIER COVERED
WHEN DOOR OPENED:
Should there still be material in the feed slot
when the door is opened, the motor switches off
and the cutters stop. The control display
comes on.
(6) comes Close the door and acknowledge the status
by pressing the forward button (3) briefly.
The existing material is fed to the cutters and
shredded.
LIGHT BARRIER COVERED
WHEN MACHINE TURNED ON:
Should there still be material in the feed slot
when the machine is switched on the control
display (6) comes on.
Remove the material and acknowledge the
status by pressing the forward button (3) briefly.
MOTOR PROTECTION:
Should the motor be overloaded it switches off.
The control display
The machine can be started again after a cooling
down period of about 25 – 40 minutes.

MAINTENANCE / DISPOSING

CUTTER MAINTENANCE (CROSS CUT):
Cross cut cutters must be oiled after a
specific operating time. If the control
display
follows:
Open the door. The control display
on and the reverse button (4) LED display
as well as the control display
Remove the oil reservoir (13) (Fig. 6) from the
holder in the door and close the door again.
Pour a little oil onto a sheet of paper and then
feed this through the paper feed slot (11) onto
the cutters.
The paper is drawn in and in this way the oil is
distributed to the cutters.
Note: This procedure is acknowledged as
follows to turn off the display after the cutters
have been oiled:
- Open the door until the control display
lights up. The control displays
13
flash.
- Press the reverse button
held down until the control display
fig. 6
out.

TECHNICAL DATA

Power supply data
supply voltage/frequency · current consumption · power
amps · 0,7 kW 120V/60Hz · 5,6 amps
amps · 0,55 kW 120V/60Hz · 5,6 amps
amps · 0,7 kW 120V/60Hz · 5,6 amps
Cutting width Cutting capacity
paper
3.8 mm
3.8x30 mm
1.9x15 mm
0.8x12 mm
0.8x4.5 mm
3.8 mm
3.8x30 mm
1.9x15 mm
0.8x12 mm
0.8x4.5 mm
45 SC2/CC3/CC4/CC5/CC6 45 SC2/CC3/CC4/CC5/CC6
60 SC2/CC3/CC4/CC5/CC6 60 SC2/CC3/CC4/CC5/CC6
(9) comes on.
(7) comes on proceed as
(8) comes
(7) flashes.
(7) and (4)
(4) and keep it
(7) goes
· 0,7 kW 100V/50/60Hz · 7,0 amps · 0,7 kW
· 0,55 kW 100V/50/60Hz · 7,0 amps · 0,55 kW
· 0,7 kW 100V/50/60Hz · 7,0 amps · 0,7 kW
Working width
paper
22-24 sheets* 235 mm
13-15 sheets* 235 mm
10-11 sheets* 235 mm
5-6 sheets* 235 mm
5-6 sheets* 235 mm
22-24 sheets* 235 mm
13-15 sheets* 235 mm
10-11 sheets* 235 mm
5-6 sheets* 235 mm
5-6 sheets* 235 mm
7
ELECTRICAL FAULT:
If the control display (9) flashes together with
the function button (2) LED display
the control display (8)
(6)
electrical fault. The machine cannot be started.
In this case please contact your dealer.
FAULT CHECK LIST:
Should the machine not work, check the following
points:
- is the plug connected to the power supply?
- is the door closed?
- is the paper collection bag full?
Follow the instructions for "EMPTYING THE
PAPER COLLECTION BAG".
- Is there a material jam in the machine?
Follow the instructions in "MATERIAL JAM IN
THE MACHINE".
- Is the motor overloaded?
See "MOTOR PROTECTION".
If none of these test points apply, please
contact your dealer.
- Close the door again.
The cutters now start a cleaning cycle
automatically (forward and reverse run) and then
switch off. The machine is ready for use again.
Should you need to re-order the special oil see

"SPECIAL ACCESSORIES".

AUTOMATIC ENERGY SAVING:
If the machine is not used for a while it
automatically switches off after about 5 minutes.
The function button (2) LED display
"Ready" goes out. Press the function button
briefly to turn it on again.
DISPOSING OF THE MACHINE:
Dispose of
environmentally friendly fashion at the
end of its useful service life. Do not
(8)
dispose of any of the parts included
in the machine or its packaging with
household waste.
SPECIAL ACCESSORIES
Description
Plastic bag, 440x330x600x0.05 mm (45)
Plastic bag, 440x330x950x0.05 mm (60)
Lubricant, 110 ml bottle
Note: For orders of special accessories and spare parts,
please contact your dealer.
Noise level Dimensions
W x D x H
app. 55 dB(A) 450 x 390 x 650 mm
app. 55 dB(A) 450 x 390 x 650 mm
app. 55 dB(A) 450 x 390 x 650 mm
app. 55 dB(A) 450 x 390 x 650 mm
app. 55 dB(A) 450 x 390 x 650 mm
app. 55 dB(A) 450 x 390 x 770 mm
app. 55 dB(A) 450 x 390 x 770 mm
app. 55 dB(A) 450 x 390 x 770 mm
app. 55 dB(A) 450 x 390 x 770 mm
app. 55 dB(A) 450 x 390 x 770 mm
* based on A4-paper 70g/m² at 230V/50Hz
or only
flashes there is an
for
the machine in an
Order-No.
83079
99977
88035
Weight
31 kg
32 kg
32 kg
32 kg
32 kg
33 kg
34 kg
34 kg
34 kg
34 kg