Briteq CLUB LASER 7 Mode D'emploi page 6

ENGLISH
DMX-CONFIGURATION:
CHANNEL DMX VALUE
0-51
Switched off
52-103 Auto Running
1
104-155 Auto Running
156-207 Sound Mode
208-255 Sound Mode
2 0-255 125 preprogrammed graphics
0-128
Rotation (rotation by Z axis)
3
129-255
Adjust the speed of the rotation
0-128
Rolling by Y Axis
4
129-255
Adjust the speed of rolling
0-128
Rolling by X Axis
5
129-255
Adjust the speed of rolling
0-128
Graphics move along the X-axis
6
129-255
Speed of moving
0-128
Graphics move along the Y-axis
7
129-255
Speed of moving
8 0-255
Drawing speed: slow to fast
9 0-255
Scanning speed: slow to fast
0-31
Original color
32-63
Yellow
64-95
Purple
96-127
Cyan
10
128-159
White
160-191
Green
120-223
Red
224-255
Blue
BRITEQ
®
USER MANUAL
DESCRIPTION
Line
Dot
Line
Dot
7/51 CLUB LASER 7
ENGLISH
5) ILDA CONTROL:
This laser can be controlled by any PC equipped with ILDA compatible software + hardware. As soon as
the ILDA-input (17) of the laser is connected with an ILDA compatible controller, it will automatically switch
to ILDA control mode. From this moment on the laser will be completely controlled by the ILDA software:
the possibilities of the ILDA software will determine what you can do or not...
ILDA soft- and hardware are available from several independent suppliers. Some possible choices are:
- PHOENIX software (www.bocatec.de)
- PANGOLIN software (www.pangolin.com)
- And many other, up to you and your finances to see what is best for your needs ...
MAINTENANCE
 Make sure the area below the installation place is free from unwanted persons during servicing.
 Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
 When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
 The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
 In order to protect the device from overheat the cooling fans and ventilation openings should be cleaned
monthly.
 The interior of the device should be cleaned annually by experienced service people.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel only!
SPECIFICATIONS
Mains Input: AC 100~240V, 50/60Hz
Fuse: 250V 1.5A slow blow (20mm glass)
Total Power consumption: 80W
Sound Control: Internal microphone
DMX connections: 3pin XLR male / female
DMX channels: 10 channels
DMX starting address: 001  256
Laser Power: 60mW Green CW laser (λ = 532nm)
300mW Red CW laser (λ = 650nm)
50mW Blue CW laser (λ = 473nm)
Laser scanners: high speed 20kHz type
Laser radiation class: 3B
Laser Safety Standard: EN60825-1:1994 + A1:2002 + A2:2002
Size (WxHxD): 58cm x 16cm (30cm with bracket) x 34cm
Weight: 11,9kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.briteq-lighting.com
BRITEQ
®
USER MANUAL
8/51 CLUB LASER 7