3M G500 Mode D'emploi page 36

An
3M™ G500 Headgear
Please read these user instructions in conjunction with the 3M™ Clear Face shield or
3M™ Mesh Face shield user instructions where you will find information on:
• Approved combinations of face shields
• Spare parts
See all instructions for use and save for continuing reference.
INTENDED USE
The 3M™ G500 Headgear with face shield is designed to protect the wearer against
impacts to the eye and face, both from the front and the side.
3M™ Mesh Face shields meet the requirements of EN1731:2006, Mesh type eye and
face protectors.
3M™ Clear Face shields meet the requirements of EN166:2001, Personal Eye Protection.
Hearing protection can be easily attached if required.
A wide range of 3M™ Peltor™ Ear muffs with Helmet attachment (P3E) are compatible
and approved for use with the 3M™ G500 Headgear.
For attenuation values and proper fitting please see the appropriate Earmuff user
instruction.
^ Particular attention should be given to warning statements where indicated.
^ WARNINGS
Always be sure that the complete product is:
- Suitable for the application;
- Fitted correctly;
- Worn during all periods of exposure;
- Replaced when necessary.
Proper selection, training, use and appropriate maintenance are essential in order for
the product to help protect the wearer from impact hazards.
Failure to follow all instructions on the use of these personal protection products
and/or failure to properly wear the complete product during all periods of exposure
may adversely affect the wearer's health, lead to severe or life threatening illness or
permanent disability.
For suitability and proper use follow local regulations, refer to all information supplied
or contact an occupational hygienist, safety professional or 3M representative on the
Tech Assist Helpline 3M Australia 1800 024 464, 3M New Zealand 0800 364 357.
Check apparatus is complete, undamaged and correctly assembled. Any damaged or
defective parts must be replaced with original 3M spare parts before use.
Eye protectors against high speed particles worn over standard opthalmic spectacles
may transmit impact energy, creating a hazard to the wearer.
Certain chemicals can cause damage to these products.
The product can cause allergic reactions on contact with very sensitive skin.
Contact 3M for additional information.
APPROVALS
These products meet the requirements of the European Community Directive 89/686/EEC
(Personal Protective Equipment Directive) and are thus CE marked.
Certification under Article 10, EC Type-Examination, has been issued for these products
by Finnish Institute of Occupational Health (FIOH), Topeliuksenkatu 41aA, FIN-00250
Helsinki, Finland (Notified Body number 0403).
CERTIFICATION
The 3M™ G500 Headgear meets the following requirements:
Model European Symbol Field of use
Standard
EN166:2001 BT High speed particles at
G500
extremes of temperature
A High speed particles
EN1731:2006 F High speed particles
Please see 3M™ Clear Face shield or 3M™ Mesh Face Shield User instructions for
details on protection offered by the face shield.
^ If the face shield and the frame are not both marked with the same symbol, the
lowest level applies to the complete face protector.
PREPARATION FOR USE
Inspect the product carefully before each use. Replace any parts that show signs of
damage such as scratches or cracks.
FITTING INSTRUCTIONS
See Figures 1-8.
1. Fitting instructions for face shields
2. Fitting instructions for Protective Ear Muffs
3. Fitting instructions for attaching the cable of any Peltor Communication product (with
P3E helmet attachment)
a) Detach the headband at the front
b) Position the cable inside the cable holder. Adapt the cable so that the same length of
cable goes to both ear muffs
c) Secure the cable using the fixing points on both sides
4. Fitting instruction for the HYG50 sweat band
5. Fitting instructions for V6* Integrated Safety Eyewear
Adjusting the fit. There are 3 different ways to achieve a good fit:
6. 3 Settings for height adjustment
7. Adjusting the length of the strap over the head
8. Adjusting the headband using the knob to fit without excessive pressure on the head
MARKING
See Figure 9. for face shield and frame markings.
1. Manufacturer
2. CE mark
3. European standard, field of use and symbol for class of impact protection
4. Type designation of face shield
5. Type designation of frame
NOTE: Other global markings (e.g. ANSI, CSA) may be present. For more information
contact 3M.
{ Date of Manufacture
? See instructions for use.
^ Warning
] Temperature Range
, Maximum Relative Humidity
TECHNICAL SPECIFICATION
G500 Headgear
Weight: 242g (without Face shield)
CLEANING INSTRUCTIONS
The product should be cleaned regularly using a mild solution of detergent in warm water.
STORAGE AND TRANSPORTATION
Do not store the product in direct sunlight or at high temperatures.
When not in use, it should be stored in a cool, dark location to prevent the material from
ageing.
The recommended maximum shelf life of the product is 5 years from the date of
manufacture.
The original packaging is suitable for transporting the product.
SPARE PARTS AND ACCESSORIES
Please see 3M™ Clear Face shield or 3M™ Mesh Face shield user instructions for details
on compatible face shields.
Mechanical
Strength
Product Code
Medium energy
HYG50
impact
V6*
High energy
NOTE
impact
Always check the markings of the face shield and face shield frame (figure 9) to ensure
Low energy
that they are compatible for use together and what protection class is valid.
impact
35
Description
Sweatband, Polyamide
Integrated safety eyewear