Publicité
Les langues disponibles
Les langues disponibles
Disposal of transport packaging
The packaging protects the machine from transit damage.
The packaging materials are generally selected to be green
and easy to dispose of and they can therefore be recycled.
Returning the packaging to the material resource system
saves raw materials and reduces the volume of waste.
Packaging parts (for example foils and polystyrene) may pose
a danger for children. There is a danger of asphyxiation!
Keep the packaging parts out of the reach of children and
dispose of them as soon as possible.
Transport and storage
•
The machine should be cleaned thoroughly before
placed in storage for a lengthy period.
•
Protect the auger from the effects of weather with a
plastic tarpaulin, cardboard or the like.
Safety information for operation
•
All safety and protective equipment must be installed
correctly and in position before the machine may be
switched on.
•
The auger must be able to turn freely.
•
Before you start the machine, ensure that the auger bit
is correctly engaged and that the moving parts of the
machine are not blocked.
•
Warning! If you are in any doubt: Ask for help
assembling the auger from a specialist at an authorised
service centre.
•
Do not use the machine until you have read the
operating manual carefully.
•
Note the safety information contained in the operating
manual.
•
Act responsibly towards other people.
Operation
Starting the auger (Fig. 1)
To start the petrol auger, we recommend that you place it
with its front on the ground.
1.
Open the gearbox vent by one turn.
2.
Set the choke to "ON"
3.
Set the ON/OFF switch to position "I"
4.
Press the throttle and lock it by pressing the locking
knob at the same time.
5.
Press the primer pump three or four times and then
pull the reversing starter.
6.
During the starting procedure, the auger bit
may turn slowly as a result of the increased idling
speed.
7.
As soon as the engine is running, the choke can be
set back to "OFF"
8.
To switch the machine off, set the ON/OFF switch
to position "0".
9.
Close the gearbox vent again.
Step-by-step instructions
.
.
.
1.
Ensure that you have secure footing in the area
where you wish to stand.
2.
Then switch on the machine.
3.
Complete the work you wish to do with the auger.
4.
Important: After completing a hole, the auger
must be switched off before being transported
to the next position.
5.
Clean the auger when you have finished work.
Troubleshooting
The engine does not start
1.
Fuel tank empty
2.
Engine flooded
3.
Spark plug dirty (carbon residues on the electrode),
electrode gap too large
4.
Carburettor jets dirty
5.
Spark plug connection, spark plug lead damaged.
–
6.
No spark
wait for 5-10 minutes and then start it again.
7.
Press the primer pump three or four times.
The motor does not develop maximum power
1.
Spark plug dirty (carbon residues on the electrode),
electrode gap too large
2.
Carburettor jets dirty
3.
Air filter dirty
4.
Exhaust, cylinder outlet duct blocked
5.
Sealing ring in the crankcase leaking
6.
Cylinder, carbon rings worn
7.
Incorrect fuel mixture (too much oil)
8.
Incorrect ignition
9.
Choke on
The engine does not stop
1.
Spark plug light grey with signs of annealing (molten
beads)
2.
Carbon residues in the combustion chamber
Safety information for inspection and maintenance work
Only a machine which undergoes regular maintenance and is
well cared for will be a satisfactory tool. A lack of
maintenance and care may result in unforeseeable accidents
and injuries.
Before starting work
Check the throttle.
Before starting work
Conduct a complete visual inspection of the machine.
Before starting work
Check that the bit is secure.
After use
Inspect the entire machine and complete any required
cleaning work.
At regular intervals
Check all the bolts to ensure that they are secure. They may
come loose over time due to vibrations.
Inspection and maintenance
IMPORTANT: The following information applies to
normal conditions of use. The intervals must be reduced
accordingly for difficult conditions and lengthy daily
working times.
Publicité
