LG VR6260 Série Guide D'utilisation page 30

SMART DIAGNOSIS
If a voice message is announced after Smart Diagnosis, refer to the following table to take proper actions.
Starting HOM-BOT smart diagnosis. Please step away and remove any
items within 1 meter, or about 3 feet.
HOM-BOT needs to be charging in order to activate smart diagnosis.
Please dock the HOM-BOT to the home station.
Starting HOM-BOT smart diagnosis. Reservation has been cancelled
for smart diagnosis. Please step away and remove any items within
1 meter, or about 3 feet.
No defect found during diagnosis.
Unable to initiate smart diagnosis due to a low battery. Please try
again after battery is charged.
Please check that the dust bin and fi lter are properly installed.
HOM-BOT will not charge due to infrared sensor error. Please try
smart diagnosis again after turning the main power switch on the
back of the HOM-BOT 'Off' then 'On' again. If the problem continues,
please contact LG Electronics customer care.
HOM-BOT will not charge due to ultrasonic sensor error.
HOM-BOT will not charge due to a problem with the cliff sensors on
bottom. Please wipe the sensors clean.
Please clean the camera sensor on bottom right side.
Please clean the obstacle detecting sensor windows on the left and
right side of the HOM-BOT.
A problem has been found on the Gyro Sensor. Please try smart
diagnosis again after turning the main power switch on the back of
the HOM-BOT 'Off' then 'On' again. If the problem continues, please
contact LG Electronics customer care.
Please check for foreign material on the left wheel.
Please check for foreign material on the right wheel.
A problem has been found on the left wheel sensor. Please try smart
diagnosis again after turning the main power switch on the back of
the HOM-BOT 'Off' then 'On' again. If the problem continues, please
contact LG Electronics customer care.
A problem has been found on the right wheel sensor. Please try smart
diagnosis again after turning the main power switch on the back of
the HOM-BOT 'Off' then 'On' again. If the problem continues, please
contact LG Electronics customer care.
A problem has been found with the brush. Please check for any foreign
material.
A problem has been found in the suction motor. Please try smart
diagnosis again after turning the main power switch on the back of
the HOM-BOT 'Off' then 'On' again. If the problem continues, please
contact LG Electronics customer care.
A problem has been found in the acceleration sensor. Please try smart
diagnosis again after turning the main power switch on the back of
the HOM-BOT 'Off' then 'On' again. If the problem continues, please
contact LG Electronics customer care.
In order to listen to the smart diagnosis result again, please press the
charging button. To stop, please press the stop button.
Smart diagnosis mode will be turned off.
Smart Diagnosis mode will not operate with the mop plate attached.
Please try again after removing it.
Smart diagnosis has failed to complete its diagnostics. Please try
again after turning the main power switch on the back of the HOM-
BOT 'Off' then 'On' again.
Please check if the charging terminal is damaged or dirty.
28
Voice message Measures (for reference)
Clear any object within a 1 m radius around Home Station, and stay
back until the diagnosis is complete.
Move Robot cleaner to the Home Station to recharge it.
Try the Smart Diagnosis again after recharging the battery.
Open the Dust Bin Cover and examine the bin.
Run Smart Diagnosis again and, if the same message is announced,
contact an LG Electronics service center.
Run Smart Diagnosis again and, if the same message is announced,
contact an LG Electronics service center.
Clean the three Cliff Sensors on the bottom at the front of the unit.
Clean the lens of Camera Sensor on the bottom-right
Clean the lens of the Obstacle Sensors on both the left and right
hand sides.
Run Smart Diagnosis again and, if the same message is announced,
contact an LG Electronics service center.
Check for foreign materials on the left wheel.
Check for foreign materials on the right wheel.
Run Smart Diagnosis again and, if the same message is announced,
contact an LG Electronics service center.
Run Smart Diagnosis again and, if the same message is announced,
contact an LG Electronics service center.
Check for any foreign material stuck in the Brush.
Run Smart Diagnosis again and, if the same message is announced,
contact an LG Electronics service center.
Run Smart Diagnosis again and, if the same message is announced,
contact an LG Electronics service center.
If you need to repeat the diagnosis result, press the 'Home' button,
or press 'Stop/OK' button to fi nish the diagnosis.
Run Smart Diagnosis again after removing the Mop Plate.
Turn the main power switch OFF and then ON again to resume the
diagnosis. Do NOT touch the robot or disturb its operation until the
diagnosis is complete.
Clean the bottom of the machine and Charging Terminal on Home
Station.