Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Contents
1.
The thicknesser at a
glance
2.
Read first!
3.
Safety
3.1 Specified
Use
3.2 General Safety Instructions
3.3 Labeling
4.
5.
height adjustment
5.6 Jointer fence installation
5.7 Connection to AC Power
6.
7.
7.1 Removal and installation of
7.4 Cleaning and Care of Machine
8.
9.
2. Read first!
These operating instructions have been
presented in a way that will allow you to
work quickly and safely with your
machine. Here are a few tips to help you
read these operating instructions:
Read all of these operating instruc-
tions prior to commissioning the
machine. Pay particular attention to
the safety instructions.
These operating instructions are
intended for people with basic tech-
nical knowledge in handling
machines such as the one described
here. If you have had no experience
with machines of this kind, you
should initially work under the super-
vision of people with previous expe-
rience.
Keep safe all documents supplied
with this machine so that you can
refer to them if required. Keep proof
of purchase for possible warranty
cases.
Should you ever lend or sell the
machine, make sure that any
machine documents are passed on
with it.
The manufacturer bears no liability
for damage caused by non-compli-
ance with these operating instruc-
tions.
Information in these operating instruc-
tions is designated as shown below:
Danger!
Risk of personal injury or
environmental damage.
Risk of electric shock!
Risk of personal injury
from electric shock.
Drawing-in/trapping haz-
ard!
Risk of personal injury
by body parts or clothing
being drawn into the
rotating saw blade.
Caution!
Risk of material damage.
Note:
Additional information.
Numbers in illustrations (1, 2, 3, ...)
indicate component parts;
are consecutively numbered; and
correspond with the number(s) in
brackets (1), (2), (3) ... in the
neighbouring text.
Numbered steps must be carried out
in sequence.
Instructions which can be carried out
in any order are indicated by bullet
points (•).
List items are indicated by dashes (-
).
3. Safety
3.1
Specified Use
This machine is intended for surface
planing and thickness planing of solid
woods. The permissible work piece
dimensions must be observed (see
"Technical Specifications").
The following tasks may not be carried
out with this tool:
ENGLISH
Insertion work (i.e. any work that
does not extend the full length of the
work piece),
Planing of cavities, pins or cut-outs,
Planing of heavily curved wood with
which there is insufficient contact
with the holding and intermediate
table.
Any other use does not comply with the
intended purpose. Unspecified use,
modification of the device or use of parts
that have not been tested and approved
by the manufacturer can cause unfore-
seeable damage!
3.2
General Safety Instruc-
tions
A thicknessing machine is a dangerous
tool which can, due to operator careless-
ness, cause serious injury.
A
Caution!
When using power tools, the following
basic safety measures must be taken to
protect against electric shock, other
injury or fire.
•
When using this pump observe the
following safety instructions to
exclude the risk of personal injury or
material damage.
•
Please also observe the special
safety instructions in the respective
chapters.
•
Where applicable, follow the legal
directives or regulations for the pre-
vention of accidents pertaining to the
use of thicknessing machines.
A
General hazards!
•
Keep your work area tidy - a messy
work area invites accidents.
•
Be alert. Know what you are doing.
Set out to work with reason. Do not
operate tool while under the influ-
ence of drugs, alcohol or medication.
•
Do not operate the machine while
under the influence of alcohol, drugs
or medication.
•
Consider environmental conditions:
Keep work area well lighted.
•
Prevent adverse body positions.
Ensure firm footing and keep your
balance at all times.
•
Use suitable work piece supports to
support the work piece when cutting
long stock. Set the work piece rests
to an appropriate height.
•
Do not operate the machine near
inflammable liquids or gases.
•
This thicknessing machine shall only
be started and operated by persons
familiar with thicknessing machines
and the dangers associated with the
operation of thicknessing machines.
en
17
Publicité
Chapitres
Table des Matières
