Safety Instructions For Drill Presses - Promac JDT-2512V Mode D'emploi

3. Do not overreach. Failure to
maintain proper working position
can cause you to fall into the
machine or cause your clothing to
get caught, pulling you into the
machine.
4. Keep guards in place and in proper
working order. Do not operate the
machine with guards removed.
5. Avoid dangerous working
environments. Do not use stationary
machine tools in wet or damp
locations. Keep work areas clean
and well lit.
6. Avoid accidental starts by being
sure the start switch is "OFF" before
plugging in the machine.
7. Never leave the machine running
while unattended. Machine shall be
shut off whenever it is not in
operation.
8. Disconnect electrical power before
servicing. Whenever changing
accessories or general maintenance
is done on the machine, electrical
power to the machine must be
disconnected before work is done.
9. Maintain all machine tools with care.
Follow all maintenance instructions
for lubricating and the changing of
accessories. No attempt shall be
made to modify or have makeshift
repairs done to the machine. This
not only voids the warranty but also
renders the machine unsafe.
10. Machinery must be anchored to the
floor.
11. Secure work. Use clamps or a vise
to hold work, when practical. It is
safer than using your hands and it
frees both hands to operate the
machine.
12. Never brush away chips while the
machine is in operation.
13. Keep work area clean. Cluttered
areas invite accidents.
14. Remove adjusting keys and
wrenches before turning machine on.
15. Use the right tool. Don't force a tool
or attachment to do a job for which it
was not designed.
16. Use only recommended accessories
and follow manufacturer's
instructions pertaining to them.
17. Keep hands in sight and clear of all
moving parts and cutting surfaces.
18. All visitors should be kept at a safe
distance from the work area. Make
workshop completely safe by using
padlocks, master switches, or by
removing starter keys.
19. Know the tool you are using — its
application, limitations, and potential
hazards.
Familiarize yourself with the following
safety notices used in this manual:
This means that if
precautions are not heeded, it may
result in minor injury and/or possible
machine damage.
This means that if
precautions are not heeded, it may
result in serious or even fatal injury.
3.3 Safety Instructions for Drill
Presses
1. All work shall be secured using
either clamps or a vise to the drill
press table. It is unsafe to use your
hands to hold any workpiece being
drilled.
2. Drill press head and table shall be
securely locked to the column
before operating the drill press. This
must always be checked prior to
starting the machine.
3. Always use the correct tooling.
Tooling shall always be maintained
and properly sharpened. All tooling
must be run at the proper speeds
and feeds as they apply to the job.
Use only recommended accessories
and follow those manufacturer's
instructions pertaining to them.
Tooling shall not be forced in to any
work piece but fed according to the
proper specifications. Failure to
follow these instructions will not only
ruin the tooling as well as the
machine, but can cause serious
injury.
4. Never brush away any chips while
the machine is in operation. All
clean up should be done when the
machine is stopped.
5. Keep hands in sight. Do not put
hands or fingers around, on, or
below any rotating cutting tools.
Leather safety gloves should be
used when handling any sharp
objects or cutting tools. See Figure
A.
6. Always wear protective eye wear
when operating, servicing or
adjusting machinery. Eyewear shall
be impact resistant, protective
safety glasses with side shields.
Figure B.
7. When drilling in material which
causes dust, a dust mask shall be
worn. See Figure C.
8. Avoid contact with coolant,
especially guarding the eyes.
9. Non-slip footwear and safety shoes
are recommended. See Figure D.
10. Wear ear protectors (plugs or muffs)
during extended periods of
operation. See Figure E.